Novoferm iso70-1 Montage-, Bedienungs- Und Wartungsanleitung Seite 9

GB
GB
Installation instructions for iso70-1 sectional
garage doors with vertical tension spring
Incorrect installation renders the door manufacturer's
liability null and void.
– Installation only by suitably qualified installers in
accordance with the requirements of EN 12604 and EN
12453 –
Please read these instructions carefully prior to installation.
Intended use of garage doors
Garage doors are intended for installation in areas
accessed by people in privately used garages. They are
for use in domestic settings to ensure articles and
vehicles, accompanied or driven by people, gain safe
access.
Although garage doors are tested to national and
international standards and manufactured in accordance
with best engineering practice, they can pose hazards.
Use of the doors is classified as improper particularly in the
following cases:

Their use does not conform to the intended use

Failure to observe the minimum protection specified in
EN 12453 during utilization

Improper maintenance or servicing, particularly by
unauthorized individuals

Application of loads exceeding normal manual
pressure on the door leaf (never apply loads to door
leaf when opening and closing; never intentionally try
to hinder opening and closing)

Use of inappropriate or incorrectly configured
operators

Installation or attachment of improper components and
parts in or to the door, the locking system or the
operator and/or modification of their original as-
delivered status

Changes to or modifications of the door or its
components

Failure to observe the assembly, operating and
maintenance instructions, respective country-specific
standards and guidelines as well as applicable safety
regulations

The door is not in safe working order

Door elements, operators and remote controls are not
children's toys
The door element is not suitable for use by people (including
children) with limited mental, physical or sensory capacities
or a lack of experience or knowledge. However, the door
can be used in areas where it is within reach of children.
A door element is not suitable for use as a load-bearing
component. The door must be installed vertically or
horizontally in keeping with its design. Accordingly, the
tracks must be perpendicular or aligned as specified in the
installation instructions.
Keep these installation, operating, and maintenance instructions in a safe place during the entire service life of the garage door!
Scope of delivery:
Iso70-1: Door leaf section set, frame set, panel set
Before commencing installation, make sure you have:
 The following tools to hand (unless you have other means of
access, place them in the garage before installing the
garage door): Folding ruler/measuring tape, spirit level,
plumber's wrench,
extension >120mm and SW 7, 10,13 and T30 spanners
(possibly open-end or socket wrench, as well), Phillips
screwdriver size 2, T30 screwdriver bit, hammer drill with
appropriate drill bit Ø10mm (depth: min. 65mm), at least 2
screw clamps, possibly squared timber (approx. 30x30mm),
hammer, chisel and metal saw.
 Suitable fastening material for the structural conditions.
Caution: Prior to use, please make sure the S8 wood
screws and S9 plugs included are suitable for the
structural conditions. Only install in areas that are
strong enough to support the load.
Caution!
When using fastening materials not included in the scope
of supply, always make sure that the type and number (e.g.
wall anchors, screws, plugs, etc.) have the capacity to bear
at least the same loads as the supplied fastening materials.
Important:
 The garage door must be mounted in the finished
opening and on the finished floor!
 Tightening torque of bolts (S3) for
hinges = 10Nm
 To be on the safe side, please compare the dimensions of
the garage with the coordinating size of the garage door
prior to commencing installation.
‒ Minimum inside width of garage
= Coordinating width + 160mm
‒ Minimum height of garage ceiling
= Coordinating width + 115mm (manually operated and
Novoport)
= Coordinating width + 130mm (ceiling pull)
‒ Minimum rebate width left and right = 35mm
 Alphanumerical combinations, for example S8, refer to
the relevant mounting material in the illustrations
section, subsequently subscripted L or R, for example
1 : parts are different for the left and right-hand sides
L
(pay attention to marking on parts), without subscript =
usable for right/left. Number combinations in square
brackets, e.g.
illustrations in the illustrations section.
 All references to left or right installation means looking
out from inside of the garage! All dimensions in
millimetres. Subject to technical alterations.
- 7 -
reversible ratchet
, refer to the corresponding
[5.10]
with