Novoferm iso70-1 Montage-, Bedienungs- Und Wartungsanleitung Seite 10

GB
GB
Door frame preassembly
Lay wood or similar protective material (to guard against
(1)
scratches) under the angular frames 1
Depending on the rebate width, bolt the wall anchor 7
loosely to the angular frames 1
S12.
Rebate width 55 - 120mm: Set the wall anchor 7
(1a)
inwards
[1.10c]
(1b) Rebate wider than 120mm: Set the wall anchor 7
outwards
[1.10c]
If using other
absorption capacity is at least equal to that of the wall
anchors supplied 7.
(2) Spacing X greater than 10 mm
Always fasten the bolt S6 pointing outwards through the wall
anchor 7 .
[1.10a]
Caution: The nut S12 must never be on the inside. This
would impair functional reliability!
Spacing X less than or equal to 10mm
Bolt S6 + washer U4 outside with wall anchor 7 and nut S12
inside .
[1.10d]
(3) Fasten the lower spring mount 5 at the lower end using two
nuts and bolts S6 + S12
Door frame assembly
(4) Position the door frames 1
against falling . Insert the frame panel 3 with the pre-
[1.15]
assembled bolts in the frames and tighten the bolts
Panel position depends on the installation situation
Use a spirit level to align the panel and door frame exactly
parallel and at right angles
screws S8 + S9 in the top corners on the left and right
Clip the panel holder 13 to the centre top of the frame panel
. When fixing the base of the frame, lay a shim U3
3 [1.15e]
beneath the screw S8
angular frames 1
R/L
process; provide suitable underlay before tightening
the screws!!! Then, finally, tighten using S8 + S9
Horizontal track pairs preassembly
(5) Bolt the right 14 or left 14
R
moulded end piece 8
from inside to outside with S6 + S12. Twist up the
[1.20c]
track mounting bracket 9
Horizontal track pairs assembly
(6) Insert the cable mount 4
Hand-tighten with S11 the moulded end piece 16
angular frame 1 and cable mount 4
R/L
with S11 the moulded end piece 16
1 . Bolt with S17 the horizontal track pairs 14
[1.25c,d]
R/L
the moulded end piece 16
(7) Bolt the track arcs 30 to the angular frames 1
S12 and to the front mounts 8 using S17 + S12 (make sure
the transition to the track profiles is smooth; use a
plumber's wrench, if necessary)
Anchor track assembly [1.30]
(8) Anchor track assembly. The anchor track 27 is intended to
be used for all suspension tasks and must be split into the
necessary sections.
(8a) Insert one anchor track 27 with connecting bracket
28 left and right into the track connector 6 and screw
to clamping plate 29 using S6 + S12 in such a way
that it can still be pulled out
(8b) If the distance to the wall is greater than 500mm, the
track connector 6 is fastened to the ceiling
(9) Using an S6 + S12, screw the track connector 6 to the
corner connecting bracket 10 so that it is finger-tight
Keep these installation, operating, and maintenance instructions in a safe place during the entire service life of the garage door!
[1.10]
/1 .
R L
left and right using S6 +
R/L
.
.
fasteners, make sure
.
[1.10c]
.
[1.10ab]
.
[1.10c]
.
[1.10b]
[1.15]
behind the opening and secure
R/L
. Once aligned, 1x fix the
[1.15]
. Caution: Make sure the
[1.15c]
are not twisted or bent during this
[1.20]
horizontal track pairs each with
L
+ end connecting bracket 10
[1.20a]
.
[1.20b]
[1.25]
into the angular frame 1
R/L
. Hand-tighten
[1.25b]
R/L
to the angular frame
R/L
and align horizontally
R/L
R/L
. Tighten bolts S11.
[1.25e]
.
[1.30a,aa]
(10) Attach the track connector 6 to the opposite corner
connecting bracket 10 and bolt both sides tightly using two
S6 + S12 screws each
(11) Fasten the track connector 6 and horizontal track pairs 14
to the wall or ceiling. Do not yet tighten the bolts S6 + S12
on the clip plate 29
(11a) Wall fastening: Pull out the anchor track 27 with the
(11b) Ceiling fastening: Bolt anchor track 27 + connecting
their load
Once aligned, tighten the clip plate 29 using S6.
Additionally secure the track mounting bracket 9 to the
ceiling with anchor track 27 + connecting bracket 28 + S6 +
S12 + 2x S8 + S9
Caution: Mount additional ceiling brackets at the front of the
track pair 14
Garage door leaf assembly
Floor section preassembly
(12) Insert floor seals 47 into floor track 89, adjust (BRB=L) and
insert rubber end plug 45
S3 to bottom section 44
Carefully cut open the protective foil around an end cap and
remove
without locks)
.
[1.15a]
bottom section
.
[1.15aa]
Bottom section assembly [1.40]
(13) Position the bottom section 44 between the angular frames
1
.
[1.15b]
R/L
underneath to allow subsequent raising of the door leaf.
Secure bottom section 44 against falling
(13a) Insert roller 56 into universal hinge 48 and install
.
[1.15a,c,d,e]
(13b) Install bottom cable mount 57
(13c) Insert the lower roller 50 together with 2x S5 into
(13d) Bolt the lower castor 50 with 2x S12 to the bottom
.
[1.25a]
R/L
Lock section
to the
R/L
(14) Insert the lock section 67 into the angular frame 1
it against falling and, as with the bottom section 44 , bolt the
to
universal hinges 48 usingS3 (M
R/L
.
[1.25e,x]
using S17 +
.
[1.30b]
.
[1.30ab]
- 8 -
.
[1.30ac,b]
(diagonal measurement).
[1.30]
connecting bracket 28 and bolt each with S8 + S9
.
[1.30ac]
bracket 28 using S6 + S12 and secure each with 2
S8 + S9 .
[1.30b]
.
[1.30c]
.
[1.30d]
R/L
[1.35]
[1.35a]
R/L
.
[1.35b]
. Attach the logo 18 (only on garage doors
[1.35ca,cb]
. Bolt the floor handle 49 using S3 to the
[1.35d]
.
[1.35e]
and place a wedge, approx. 30mm (wood or similar)
universal hinge 48 on bottom section 44 usingS3
(M =10 Nm) [
.
1.40a,b]
A
section 44 with 4x S3 (M
A
bottom cable mount 57
R/L
cable mount 57 .
[1.40e]
R/L
[1.45]
A
R/L
. Fasten floor track 89 +
.
[1.40]
to the bottom
R/L
=10Nm)
[1.40c]
.
[1.40d]
, secure
R/L
=10Nm) .
[1.45a]