Cleaning The Feeder - Zummo Z40 Bedienungsanleitung

 Z40 o Service Model
- Remove the filter tray or the tank with its filter to get access to the nuts fixing the squeezer tray
(Fig. 13a-13b).
- Remove the squeezer tray, blade and cups simultaneously. To do so, gently unscrew the nuts
securing the cups and, using them as supports, pull outwards and they will come loose so they
can be removed easily. Unscrew the nuts of the tray shafts and pull outwards horizontally to
remove all the parts (Fig. 14).
For a very thorough clean, unscrew the balls inside the squeezer tray (Fig. 15); underneath them
there should be a washer. You can either put these parts in a dishwasher or wash them by hand.
TAKE GREAT CARE WITH THE BLADE (Fig. 3) as it is very sharp and could cause cuts.
 Self-service model
- Unscrew the nuts of the shafts of the tray and pull outwards horizontally to remove the faucet
tray and the filter (Fig. 16).
Clean the faucet tray with a cloth moistened in a neutral soapy solution (IMPORTANT! NEVER
clean it with abrasive products which might scratch it).
- Remove the squeezer tray, blade and cups simultaneously. To do so, gently unscrew the
fastening nuts and, using them as a support, pull outwards and they will come loose so they can
be removed easily.
For a very thorough clean, unscrew the balls inside the squeezer tray (Fig. 15); underneath them
there should be a washer. You can either put these parts in a dishwasher or wash them by hand.
TAKE GREAT CARE WITH THE BLADE (Fig. 3) as it is very sharp and could cause cuts.
Assembly
After cleaning the whole unit, it is re-assembled as follows:
1 Screw the balls into the squeezer tray. Make sure you have fitted the washers first and TIGHTEN the
balls well! Then, adjust the position of the balls as you can see in the picture, the slots must coincide
with the mark of the tray. (Fig. 17).
2 Insert the blade in the squeezer tray and slot the ribs into the grooves of the balls (Fig. 18). Check
that the blade slides easily.
3 Square up the squeezer tray set and blade to their respective shafts (Fig. 19) and then insert the
cups in the squeezer tray and square them up to the shafts (Fig. 20). Assemble this set in the
machine at the same time and tighten the nuts well.
4 Fit the shafts and the pulp scraper filter in the filter, fit the filter correctly in its position in the filter tray,
self-service tray or tank (THE DRIVE SHAFT SHOULD OVERHANG THE TRAY OR TANK – Fig.
21a-21b-21c) and fit the set into the machine. Check that the tray or tank is fitted properly which will
also indicate that the filter is in the right position (THE DRIVE SHAFT (Fig. 22a) SHOULD
DOVETAIL WITH THE HEXAGONAL FILTER ACTUATOR – Fig. 22b).
5 Fit the sides covers to the machine (Fig. 12b).
6 Finally, fit the cover to the sides covers (Fig. 11).
Before operating the machine, make sure that:
Juice tray and Blade are properly fitted in place.

Fastening Nuts are properly tightened.

The correct set of squeezing parts (Balls, Cups and Fruit Selector) are fitted. (see "Accessories" in this

manual).
If Blade, Juice tray, Balls or Cups are not correctly assembled, serious damage may be caused to these
parts or to the interior components of the machine.
(Z40 or Z40 Service Model) The display will show the number of oranges to be squeezed. The machine is
now ready for operation.
(Self-service Model) When the machine is ready to work, the display show the "machine icon and the
orange icon".

Cleaning the feeder

 Remove the external basket by turning it gently (Fig. 23).
 Unscrew the Nut located inside the basket. (Fig. 24)
 Remove the Hopper Fruit Classifier pulling it upwards. (Fig. 25)
20
(Operator faults not covered by the guarantee)