Muting Channels; Overview Of The Signal Paths - IMG STAGELINE DMIX-20/2 Bedienungsanleitung

5.3.5 Muting channels

All input channels, subgroups, Aux ways, internal effect ways and
the sum channel MAIN can be separately muted when they are not
needed, for example� This muting will also apply to any extracted
signal (AUX, FX) of the muted channel, no matter whether it has
been set to PRE or POST�
1) Use the appropriate key (7, 8, 11) to select an input channel, Aux
way, subgroup or the sum channel MAIN�
Note: A subgroup or an Aux way can only be selected via these keys when
the key AUX-FX MODE (12) is not illuminated; if required press the key so
that it extinguishes�
2) To mute, press the key MUTE (23) so that it lights up�
3) To unmute, press the key MUTE again�
When the function "Pre-Fader Listening" is switched on [key PFL (17)
illuminated], it is possible to monitor the signal (
while muting is activated�
With the key FX MUTE (14), the two internal effect ways can always
be directly muted or unmuted simultaneously�

5.3.6 Overview of the signal paths

The screen view "Assign" (fig� 9) offers an overview of the signal
path of an input channel or FX channel� The screen view can be called
up with the key ASSIGN (22) (channel must be selected); it will be
automatically displayed when the key AUX-FX MODE (12) is pressed
to assign an Aux way or internal effect way�
Gate PEQ
Assign
Channel Comp GEQ
DCA Assign
Left
DCA 1 DCA 2 DCA 3
DCA 4 DCA 5 DCA 6
Assign
Main Sub1 Sub2
Sends
AUX1 AUX2 AUX3
-10.5dB -10.5dB -10.5dB
PRE PRE PRE
Select
48V Link INV.
Channel
Fig. 9 Assign
The screen view "Routing" provides an excellent overview of all as-
signed signal paths within the mixer, related to a sum channel:
1) Press the key SYSTEM (16) twice�
2) Use the appropriate key (7) or (11) [not (23)!] to select the sum
channel (AUX, SUB, FX, MAIN) to be displayed in the overview�
3) Figure 10 is an example overview of a subgroup� For each input
channel and each internal effect way, the overview indicates
whether it is assigned to the subgroup (ON) or not (OFF)� To change
an assignment, tap the appropriate button on the screen�
4) Figure 11 is an example overview of an Aux way� For each input
channel and each internal effect way, the overview indicates the
signal part assigned to the Aux way and whether the signal is
picked up ahead of the channel fader (PRE) or after the channel
fader (POST)�
To change the position of the signal pick-up, tap the appropriate
button on the screen� To adjust the signal part, tap the appropriate
control on the screen and then use the rotary knob PARAMETER
ADJUST (18)�
☞
chapter 5�1�5)
System Mixer Long
FX 1
FX 2 Routing DCA Faders
Pan
Right Parameter
Aux 1
-10.5dB
Sub3 Sub4
AUX4 FX1 FX2
-10.5dB -10.5dB -10.5dB
PRE POST POST
Copy
Load Save
Assign Gate
Channel Comp
CH01 CH02
OFF OFF
CH09 CH10
ON ON
CH17-18 CH19-20
OFF OFF
Fig. 10 Routing SUB 1
Assign Gate
Channel Comp
CH01 CH02 CH03
OFF OFF OFF
PRE PRE PRE
CH09 CH10 CH11
OFF OFF OFF
PRE PRE PRE
CH17-18 CH19-20 FX1
OFF OFF OFF
PRE PRE PRE
Mute
9dB
Fig. 11 Routing AUX 1
CH08
Solo
CH08
PEQ FX 1 System Mixer
GEQ FX 2 Routing DCA
CH03 CH04 CH05 CH06
OFF OFF OFF OFF
CH11 CH12 CH13 CH14
ON ON OFF OFF
FX1 FX2 USB
OFF OFF OFF
Select
PEQ FX 1 System Mixer
GEQ FX 2 Routing DCA
CH04 CH05 CH06 CH07
OFF -11.0dB -11.0dB OFF
PRE PRE PRE PRE
CH12 CH13 CH14 CH15
OFF OFF OFF OFF
PRE PRE PRE PRE
FX2 USB
ALL
OFF OFF Select
PRE PRE
Long
Faders
CH07 CH08
OFF OFF
CH15 CH16
OFF OFF
SUB1
Long
Faders
Parameter
CH08
CH01
OFF OFF
OFF
PRE
CH16
OFF
PRE
POST
AUX1
31