IMG STAGELINE DMIX-20/2 Bedienungsanleitung Seite 25

11 Keys AUX 1– 4 and FX 1/ 2 to select an AUX way or effect way for
additional settings or to select a Send control [depending on the
setting of the key AUX-FX MODE (12)]
12 Key AUX-FX MODE to switch between the two functions available
for the keys AUX 1– 4 and FX 1/ 2 (11):
When the key AUX-FX MODE is illuminated, the keys AUX 1– 4
and FX 1/ 2 can be used to select an AUX/FX Send control for the
current channel�
When it is not illuminated, the keys AUX 1– 4 and FX 1/ 2 can be
used to select an Aux way or effect way for additional settings�
13 Key DCA to define the level control groups:
The key will start flashing when pressed for the first time� While
the key keeps flashing, select the desired channels for the DCA
group selected� To complete the group definition, press the key
DCA again; the key will extinguish�
14 Key FX MUTE to mute the two internal effect ways
15 Volume controls CTRL ROOM (control room), HP1 and HP2 (head-
phones) for the signal of the Solo bus
16 Keys to call up superordinate screen views
METER Overview of all level settings and signal levels
SYSTEM General system settings;
when pressed for a second time: overviews of all signal
path assignments
17 Key PFL (Pre-Fader Listening) to change the signal pickup setting
for the Solo bus
Key illuminated: the signals will be picked up ahead of level setting
and independently of muting
Key not illuminated: the signals will be picked up after level setting
18 Rotary knob PARAMETER ADJUST to adjust a parameter selected
and direction keys ,  ,  , to select a parameter or channel,
to change a value etc� (functions will deviate, depending on the
screen view selected)
19 Key FLAT EQ to reset an equalizer setting, depending on the screen
view selected
20 Key (TAP)/ ENTER to confirm confirmation prompts and, by rhyth-
mically pressing the key, to define echo times for the delay effects
of the effect processors
21 Key GEQ to call up the screen view for the graphic equalizers
22 Keys to call up specific screen views
MIXER Overview of all input channels and output channels
Setting options:
– Level
– Position in stereo panorama /Stereo balance
– Signal path assignments
– Muting
– Solo selection
– Linkage of two adjacent channels as a stereo pair
Press the key repeatedly to go from the overall view to
the partial view (with long faders) and vice versa�
ASSIGN Overview of the settings of the channel selected
For the input channels and the effect ways FX1/ 2, press
the key repeatedly to go to a second view�
GATE / Settings of the dynamic-range processors noise gate/
COMP compressor for the channel selected
For the input channels and the effect ways FX1/ 2, press
the key repeatedly to go from the noise gate to the
compressor and vice versa�
PEQ/ Settings for sound correction of the selected channel
GEQ by means of high-pass filter, low-pass filter and four
parametric filters
Press the key repeatedly to change between the view
of a graphic equalizer for the sum channel MAIN, for a
subgroup or for an Aux way�
FX 1/ 2 Settings of the two effect processors
Press the key repeatedly to go from FX1 to FX2 and
vice versa�
DIGITAL Settings for the inputs and outputs of the optional
32-channel digital audio interface
48 V Screen view to switch the phantom power supply for
the individual microphone inputs on and off
Caution: Never switch on the phantom power supply when
audio sources with unbalanced outputs are connected; other-
wise, the audio sources may be damaged�
Prior to switching the phantom power supply on or off, always
mute the channel and adjust the outputs for the headphones and
the control room (15) to a low volume� High-volume switching
noise may damage your hearing and the speakers�
23 Keys for signal path assignments of the channel selected
SOLO Will switch the channel to the Solo bus which is used
to separately monitor the signals via the headphone
outputs, the output CTRL ROOM and the level indicator
SOLO METER (3)
MUTE Will mute the channel
PAN Will place the signal of the channel in the stereo
panorama
The adjustment is made by means of the rotary knob
PARAMETER ADJUST (18)� For stereo inputs or mono
inputs linked as a stereo pair, the key PAN is used to
adjust the balance of the stereo signal�
MAIN Will route the signal to the sum channel MAIN
SUB 1– 4 Will route the signal to the appropriate subgroup
LINK Will link the mono channel selected and its adjacent
channel as a stereo pair
The settings of the channel selected will be adopted
by the other channel� As long as the two channels are
linked, all settings will apply to both channels (excep-
tions: input gain, phantom power supply)
24 Motor fader to adjust the signal level of the channel selected (input
channel, Aux way, effect way, subgroup, sum channel MAIN)
When another channel is selected, the motor fader will automati-
cally go to the value of the channel selected� When this parameter
is changed via the screen or the rotary knob PARAMETER ADJUST
(18), the setting of the motor fader will change accordingly�
25 Controls for the signal level of the subgroups SUB 1– 4 (AUX 5 – 8)
and of the sum channel MAIN
26 Headphone output HP 1 (6�3 mm stereo jack) to monitor a signal
by means of the Solo bus
25