5�8 Dca Groups; Creating A Dca Group; Mixing By Means Of Dca Groups, Muting Groups; 5�9 Digital Outputs - IMG STAGELINE DMIX-20/2 Bedienungsanleitung

5.8 DCA groups
Any channels can be grouped in 6 DCA groups� Unlike as with sub-
groups, the signals of a DCA group are not mixed: It is only possible
to simultaneously control the signal levels of all channels contained
in a group by means of the corresponding fader (DCA = Digitally
Controlled Amplifier)� The mixing ratio of the levels adjusted via the
channel faders will be retained, i� e� the gain values of the DCA controls
and the channel faders will be taken into account:
Example:
Channel fader = −6 dB, DCA fader = +3 dB ➾ resulting gain = –3 dB

5.8.1 Creating a DCA group

To create or modify a DCA group:
1) Press the key DCA (13)� The key will start flashing and the screen
view "DCA Set" (fig� 26) will be displayed�
2) Tap the appropriate button DCA 1– 6 on the right side of the screen
to select the DCA group to be created�
3) Use the keys (7, 8, 11) or tap the appropriate control on the screen
to select all channels that are to be included in the DCA group� The
keys will light up and the corresponding sections on the screen will
be highlighted in colour�
Channels linked as a stereo pair can only be selected together�
4) To deselect a channel, press the appropriate key again�
5) To remove all assignments to the DCA group, tap the button "DCA
Clear"� A confirmation prompt will appear: Tap "Yes" or press the
key ENTER (20) to confirm�
6) Press the key DCA (13) or tap the button "DCA Set"� The mixer will
go to the view "Mixer"; the DCA group just created will be selected�
In the mixer views, individual names can be assigned to DCA groups
just like to the other channels (
3.0dB 3.0dB 3.0dB
Back
To
Previous
CH01 CH02 CH03
3.0dB 3.0dB 3.0dB
System
CH09 CH10 CH11
3.0dB 3.0dB 3.0dB
DCA Set
AUX1 AUX2 AUX3
3.0dB 3.0dB 3.0dB
DCA Clear
CH17-18 CH19-20 FX1
Fig. 26 DCA Set
Note: The coloured symbols DCA 1– 6 in the upper left of the screen view "As-
sign" (fig� 9) also indicate that a channel has been assigned to a DCA group:
DCA 1 DCA 2 DCA 3
In the figure to the left, the channel has been
DCA 4 DCA 5 DCA 6
assigned to the DCA groups 1 and 4�
Fig. 27
☞
chapter 6�1)�
3.0dB 3.0dB 3.0dB 3.0dB 3.0dB
CH04 CH05 CH06 CH07 CH08
3.0dB 3.0dB 3.0dB 3.0dB 3.0dB
CH12 CH13 CH14 CH15 CH16
3.0dB 3.0dB 3.0dB 3.0dB 3.0dB
AUX4 SUB1 SUB2 SUB3 SUB4
3.0dB 3.0dB
1.Select DCA Group 1 to 6
2.Highlight/Assign Channels
to DCA Group
3.Click "DCA Set" to Confirm!
FX2 USB

5.8.2 Mixing by means of DCA groups, muting groups

1) To control the level of a DCA group, press the key DCA 1– 6 (10)
for the group desired� The screen will display the view "Mixer"
(fig� 20), the key will be illuminated and the corresponding button
on the screen will be highlighted in colour� In addition, all channels
assigned will be highlighted in colour on the screen�
If you try to call up a DCA group that has not been defined yet, a
corresponding message will be displayed�
2) The motor fader (24) can now be used to operate the fader of
the group selected and thus to adjust the levels of the channels
contained in this group� Or the group can be muted with the
button MUTE (23)�
3) The button SOLO (23) can be used to set all channels of the group
to the Solo bus for monitoring (
channels, the assignment to the Solo bus will be removed�
4) To go to the view that shows the 6 faders of all DCA groups on a
single screen, press the key MIXER (22)�
Note: The setting of the DCA group will remain in effect when another DCA
group is selected and operated� When a channel is assigned to multiple DCA
groups, the resulting gain for this channel will depend on all DCA faders assigned�
5.9 Digital outputs
At the jack USB AUDIO (35), the sum signal MAIN will always be
available�
When the extension module for digital inputs and outputs is installed
☞
( chapter 4�4), the signal of each analog input channel and output
channel as well as the signal of the Solo bus will be additionally avail-
able as a digital output signal�
1) Use the key DIGITAL (22) to call up the screen view "Digital Output"
(fig� 28) (press the key twice, if required)�
2) Tap the appropriate section on the screen view to switch the digital
output for the corresponding channel ON or OFF�
Long Fader
3) When a channel has been selected (section highlighted in blue),
the rotary knob PARAMETER ADJUST (18) can be used to adjust
DCA 1
the gain for the digital signal�
Drums
When no extension module is installed, "Please insert the optional
DCA 2
digital card!" will be displayed�
Back Vocals
DCA 3
Aux & Fx
Assign Gate
Channel Comp
DCA 4
DCA 4
0.0dB 0.0dB 0.0dB
DCA 5
CH01 CH02 CH03
DCA 5
OFF OFF
DCA 6
0.0dB 0.0dB 0.0dB
DCA 6
CH09 CH10 CH11
OFF OFF
-10.5 dB 0.0dB 0.0dB
AUX1 AUX2 AUX3
ON OFF OFF
0.0dB 0.0dB 0.0dB
SUB1 SUB2 SUB3
OFF OFF
Fig. 28 Digital Output
☞
chapter 5�1�5); for all the other
PEQ FX 1 System
GEQ FX 2 Routing
0.0dB 0.0dB 0.0dB
CH04 CH05 CH06
OFF OFF OFF OFF
0.0dB 0.0dB 0.0dB
CH12 CH13 CH14
OFF OFF OFF OFF ON
0.0dB 0.0dB 0.0dB
AUX4 CH17-18 CH19-20
OFF ON OFF OFF ON ON
0.0dB 0.0dB 0.0dB
SUB4 Main Solo
OFF OFF OFF OFF
Mixer Long
DCA Faders
Parameter
AUX1
0.0dB 0.0dB
-10.5 dB
CH07 CH08
OFF OFF
0.0dB 0.0dB
CH15 CH16
OFF OFF
Digital Input
Digital Output
37