Hazards Caused By Accessories; Hazards In The Workplace; Hazards Caused By Dust And Vapours - Parkside PDTS 6.3 B3 Originalbetriebsanleitung

■ If the operator notices symptoms such as persis-
tent or recurring illness, discomfort, throbbing,
pain, tingling, burning or stiffness, these indica-
tions should not be ignored. The operator must
inform his/her employer and seek the advice
of a suitably qualified medical practitioner.

Hazards caused by accessories

■ Disconnect the abrasive grinding machine from
the power supply before mounting or replacing
the machine tool or accessory.
■ Use only accessories and consumables of the
sizes and types recommended by the manu-
facturer of the abrasive grinding machine. Do
not use other types or sizes of accessories and
consumables.
■ Make sure that the dimensions of the abrasive
medium are compatible with those of the abra-
sive grinding machine and that the abrasive
medium fits on the spindle.
■ Make sure that the thread type and size of the
abrasive medium exactly matches the thread
type and size of the spindle thread.
■ Inspect the abrasive medium before use.
Do not use abrasive media that may have been
dropped or have chips, cracks or other defects.
■ Ensure that the abrasive medium is properly
fixed and tightened before use; the abrasive
grinding machine must be operated for at least
1 minute in a secure position at idling speed;
the machine must be switched off immediate-
ly if significant vibration or other damage is
detected; the cause of these faults must be
determined.
■ By checking the dimensions and other important
data of the spindle, you can avoid the spindle
end touching the bottom of the opening of
grinding pots, cones or die grinders with thread-
ed inserts intended for mounting on machine
spindles.
■ For abrasive media which are supplied with re-
ducers or bushings or which are to be used with
reducers or bushings, the user must ensure that
the reducer or bushings do not touch the face of
the clamping flange and that the clamping force
provides sufficient rotational drive to prevent the
abrasive from slipping.
PDTS 6.3 B3
■ In cases where clamping flanges are provided
for different types and sizes of abrasives, always
attach the correct clamping flange for the abra-
sive medium being used.
■ Avoid direct contact before and after using the
machine tool, as it may be warm or sharp.
■ The abrasive medium must be stored and hand-
led in accordance with the manufacturer's
instructions.

Hazards in the workplace

■ Slipping, tripping and falling are the main
causes of injuries in the workplace. Look out
for surfaces which could have become slippery
due to use of the machine, and also any tripping
hazards caused by air or hydraulic hoses.
■ Proceed with caution in unknown surroundings.
Hidden hazards caused by power or other supply
lines may be present.
■ The abrasive grinding machine is not intended
for use in explosive atmospheres and is not
insulated against contact with electrical power
sources.
■ Make sure that there are no electrical lines, gas
pipelines, etc., which could lead to a hazard
in the event of damage due to the use of the
machine.

Hazards caused by dust and vapours

■ The dusts and vapours generated by the use
of sanding machines for abrasive sheets and
polishers can cause health problems (such as
cancer, birth defects, asthma and/or dermati-
tis); it is essential to carry out a risk assessment
of these hazards and to implement appropriate
control mechanisms.
■ The risk assessment should include all dust
caused by use of the machine and any existing
dust which may be kicked up at the same time.
■ The abrasive grinding machine is to be operated
and maintained in accordance with the recom-
mendations contained in this manual to keep
the release of dust and vapours to a minimum.
■ The exhaust air should be routed so that the
raising of dust in already dusty environments is
kept to a minimum.
GB │ IE │
19 ■