Operation Time - 3M PELTOR WS ALERT XP Anleitung

GB
Safety Helmets Attachment
E:4 Insert the hard hat attachment in the slot on the
hard hat and snap it into place E:5.
E:6 Ventilation mode: To switch the unit from work mode
to ventilation mode, pull outward on the ear cups until you
hear a click E:7.
E:8 Avoid placing the cups against the hard hat as this
prevents ventilation.
OPERATING INSTRUCTIONS
CHARGING AND REPLACING THE BATTERIES (FIG. 1)
1. Detach the latch on the left cup with your fingers.
2. Open the cup.
3. Insert or replace the batteries. Make sure the polarity
corresponds to the markings.
4. Close the cup and lock the latch. Change the battery type
if you are switching from rechargeable to non rechargeable.
Long press (2 s) the Menu button [M] to access the
configuration menu, see "Configuring your headset".
CAUTION: Use only 3M™ PELTOR™ USB charger
FR09 EU and 3M™ PELTOR™ USB wall adapter FR08
with 3M™ PELTOR™ LR6NM rechargeable batteries
(or equivalent AA Ni-MH rechargeable batteries.)
CAUTION: The battery may not be charged if the
ambient temperature exceeds +45 °C.
NOTE:
- Do not charge alkaline batteries as this may cause damage
to the headset.
- Only use AA non-rechargeable or Ni-MH rechargeable
battery.
- Do not mix old and new batteries. Do not mix alkaline,
standard, or rechargeable batteries. To properly dispose
of the battery, follow local solid waste disposal regulations.

OPERATION TIME

Approximate use time with new AA alkaline batteries and fully
charged LR6NM rechargeable batteries (2100mAh):
- FM radio and level-dependent: approx 58 hours
- Bluetooth streaming and level-dependent: approx 78 hours
®
NOTE:
Depending on the environment, temperature, and battery,
the operation time may vary.
POWER ON/POWER OFF (fig. 2)
Long press (2 s) the Power button [
headset on or off.
A voice message will notify "Power on" or "Power off".
The first time the headset is powered on, it automatically
enters pairing mode.
NOTE: If no button has been pressed for 4 hours, the headset
will automatically be powered off. A voice message will notify
"Automatic power off".
3
] to power the
** 3M™ PELTOR™ WS™ ALERT™ XPI Headset
ADJUSTING THE SOUND SOURCE VOLUME LEVEL (fig. 3)
Adjust the sound volume level, short press (1 s) the [ + ] or [–]
button. Change the active sound source by short press (1 s)
the Power button [ ].
The sound source can either be:
• FM radio
• Phone
• Surround
• Music
• Bluetooth
®
SMART TIP: You can configure bass boost, surround
balance, and surround equalizer. Long press (2 s)
the Menu button [M] to access the configuration menu.
See Configuring your headset.
Surround sound (Level-dependent microphone for
ambient listening)
Helping protect your hearing from potentially harmful noise
levels. Constant rumbling and other potentially harmful noises
are reduced to a level below 82 dB, but you can still speak
normally and make yourself heard.
COMMUNICATION FACE TO FACE (PUSH-TO-LISTEN) **
(fig. 4)
The Push-To-Listen feature enables you to instantly listen
to your environment by muting the FM radio and Bluetooth
audio volume and activating the level-dependent micro-
phones. Short press (1 s) two times the Power button [
to activate Push-To-Listen. Short press any button to
deactivate Push-To-Listen (PTL).
LISTEN TO FM RADIO
Search station (fig. 8)
Short press (1 s) the Menu button [M] to enter search
station mode. Short press (1 s) the [ + ] or [–] button to initiate
a search. The radio station frequency will be confirmed by
a voice message.**
SMART TIP: If you short press (1 s) the Menu button [M],
you will always start the FM radio.
NOTE: Radio reception depends on the topography and the
environment you are in. If the reception is poor, try to change
area if possible.
Store station (fig. 9)
Short press (1 s) three times the Menu button [M], voice
message "Store station". Short press (1 s) the [ + ] or [–]
button to select position. Long press (2 s) the Menu button
[M] to store the station. A voice message will confirm
"Confirmed".
Preset station (fig. 10)
Short press (1 s) two times the Menu button [M] to enter the
preset station mode. A voice message will confirm "Preset
station". Short press (1 s) the [ + ] or [–] button to browse and
select preset station. The radio station frequency will be
confirmed by a voice message.
®
]