Important Information - elco CB-P2.170 G-U/TCG KN Betriebsanleitung

Overview
Contents
Overview
Function
Assembly
Commissioning
Servicing

Important information

The burners P2.xxx G-U/TCG burners are
designed for the low-pollutant combustion of
natural gas and propane gas. The design
and function of the burners meet standard
EN 676.They are suitable for use with all
heat generators complying with standard EN
303 or for use by hot air generators
complying with standard DIN 4794 or DIN
30697 within their respective performance
range. Any other type of application
requires the approval of ELCO. Installation,
commissioning and maintenance must only
be carried out by authorised specialists and
all applicable directives and regulations
must be complied with.
Burner description
The burners P2.xxx G-U/TCG are single-
stage, fully automatic, monoblock type
burners. The special design of the burner
head provides low-polluting combustion with
high efficiency. In line with testing as defined
by EN676, the values comply with emissions
class 3 - the most stringent standard - and
also fulfils the requirements of national
environmental legislation:
AT:KFA 1995, FAV 1997
CH:LRV 2005
DE: 1.BImSChV
NL: EN676, emission class 3
Emissions values may differ, depending on
combustion chamber dimensions,
combustion chamber load and the firing
system (three-pass boilers, U-fired boilers).
For specifying warranty values, the
conditions for the measuring equipment,
tolerances and humidity must be observed.
The following standards should be observed
in order to ensure safe, environmentally
sound and energy- efficient operation:
EN 676
Forced-draught gas burners.
EN 226
Connection of vaporising oil and forced-
draught gas burners to the heat generator.
66
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Important information . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Burner description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Control unit
Standard function without leakage test, . . . . . . . . . . . . . .68
Standard function with leakage test . . . . . . . . . . . . . . . . .69
Quick start with continuous motor operation
Quick start with longer preventilation . . . . . . . . . . . . . . . .70
Allocation chart, connection socket . . . . . . . . . . . . . . . . . 71
Operating function without leakage test,
without leakage test, safety function . . . . . . . . . . . . . . . . .72
Burner assembly, gas connection . . . . . . . . . . . . . . . . . .74
Operating function with GPL, electrical connection . . . . .75
Checks before commissioning,
Ionization current measurement . . . . . . . . . . . . . . . . . . . .76
Adjustment data, air regulation
Setting the air pressostat, gas pressostat, . . . . . . . . . . . . .
operating check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Maintenance frequency indicator . . . . . . . . . . . . . . . . . . .81
EN 60335-2
Safety of electrical equipment for domestic
use.
Gas lines
When routing gas lines and trains, observe
the general installation regulations and
directives as well as national guidelines:
CH: - SVGW gas directives G1.
- EKAS Form.1942 Liquefied
Petroleum Gas- directive, part 2.
- Regulations on cantonal
instances (e.g. fire department
regulations).
DE: - DVGW-TVR/TRGI
Place of installation
The burner must not be used in rooms
exposed to aggressive vapours (e.g.
hairspray, tetrachloroethylene or carbon
tetrachloride), large amounts of dust, or high
levels of air humidity (e.g. in laundry rooms).
An air inlet must be present with:
DE: up to 50 kW: 150cm
+ 2,0cm
CH: QF [kW] x 6= ...cm
2
200cm .
Variations may arise as a result of local
regulations.
We can accept no warranty liability
whatsoever for loss, damage or injury
caused by any of the following:
- Inappropriate use
- Incorrect assembly or repair by the
customer or any third party, including the
fitting of non-original parts.
Provision of the system and the
operating instructions
The firing system manufacturer must supply
the operator of the system with operating
and maintenance instructions on or before
final delivery. These instructions should be
displayed in a prominent location at the point
of installation of the heat generator, and
should include the address and telephone
number of the nearest customer service
centre.
05/2014 - Art. Nr. 420010540302
Page
. . . . . . . . . . . . . . . . . . . .77
2 for additional kW
2 .
2
; but at least
Declaration of conformity
for gas burners
We ,
ELCO
declare under our sole responsibility
that the gas burners named
P2.170 G- U/TCG
P2.250 G- U/TCG
conform to the following standards :
EN 676: 2008
EN 60335-1: 2008
EN 60335-2-30: 2006
EN 60335-2-102: 2007
EN 55014-1: 2008 + A1: 2009
EN 55014-2: 1998 + A1: 2001 + A2:
2008
These products bear the CE mark in
accordance with the stipulations of
the following directives:
2009/142/EEC Gas Appliance
Directive
2006/95/EEC Low Voltage Directive
2004/108/EEC EMC Directive
2006/42/EC Machinery directive
Resana, June 2013
C. RENA
Notes for the operator
The system should be inspected by a
specialist at least once a year. It is
strongly recommended to take out a
service contract to guarantee regular
servicing.