Herunterladen Inhalt Inhalt Diese Seite drucken

Aligning The Motion Detector; Installation Start-Up; Automatic Operation; Adjusting The Light Sensitivity (Lux) - LIVARNOLUX LSL 32 A2 Bedienungs- Und Sicherheitshinweise

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Notice:
If the lighting angle is not ideal, switch the light off
and allow to cool down for 15 minutes. Loosen the
adjusting screws
with a screwdriver and read-
4
just the lighting angle. Then tighten the adjusting
screws
.
4
Start-up
Note: The LED light has a motion detector
which responds to temperature changes.
The motion detector
9
peratures below 20 °. A moving object with a tem-
perature near the ambient temperature is difficult to
detect.
Note: The control dials are located below the
motion detector
(Fig. A).
9
Note: The maximum range of the motion
detector
is approx. 12 m, the detection radius
9
approx. 180 °.
Note: The horizontal directional radius of the
motion detector
is approx. 130 °. The vertical
9
directional radius of the motion detector is
approx. 90 °.
Do not adjust the motion detector
force. The safety stops could break.

Aligning the motion detector

Note: The detection area must be well within range
of the infrared beams from the motion detector
The view of the detection area must not be obstructed
by objects such as plants etc. Infrared beams cannot
pass through solid objects.
Note: The detection area should run transversely
to the direction of passage and be kept as small as
possible. A large detection area increases the risk
of the light being switched on for irrelevant reasons.
1. First align the motion detector
2. Then loosen the locking screw (motion detector)
by turning it counter-clockwise.
5
3. Now align the motion detector
tighten the locking screw (motion detector)
clockwise.
9
works best in ambient tem-
with
9
horizontally.
9
vertically and
9
4. Test your settings by walking slowly into the de-
tection area. Repeat steps 1 to 3 until you achieve
the desired result.

Automatic operation

Adjusting the sensor sensitivity (SENS):
Adjust the sensor sensitivity to your preferences
using the SENS rotary control
Turn clockwise to increase the sensor sensitivity.
Turn counter-clockwise to decrease the sensor
sensitivity.
Note: The further right the rotary control is turned,
the more sensitive the motion detector will be, i.e. it
will already respond to minor temperature changes
within the detection range. If the sensitivity is set too
high, even small animals or movement from leaves
(from trees or shrubs) may already trigger the motion
sensor, inadvertently activating the light.
Adjusting the on duration (TIME):
Set the light on time (5 s–10 min) using the
TIME rotary control
Turn clockwise to increase the on time. Turn
counter-clockwise to decrease the on time.

Adjusting the light sensitivity (LUX):

Set the desired light sensitivity using the LUX
rotary control
Turn clockwise to increase the light sensitivity.
.
The light is more sensitive to changes in light in-
9
tensity and switches to automatic mode sooner.
Turn counter-clockwise to decrease the light
sensitivity. The light is less sensitive to changes
in light intensity and takes longer to switch to
automatic mode.
Note: If the LUX rotary control
sition, the motion detector will work
If the LUX rotary control
motion detector
Note: Once the light has been activated by the
motion detector
5
If new movement is detected during this time, the
original period will be extended by this set amount
of time.
Installation / Start-up
.
6
.
7
.
8
is in the
8
day and night.
9
is in the
position, the
8
will only work at night.
9
, it will remain on for the set time.
9
po-
GB
9

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis