Configuration Menu - Aventics ECD-IV Betriebsanleitung

AVENTICS | ECD-IV | R412025990–BAL–001–AC | English
Adjusting the software menus
The menu is operated using three buttons. Settings are adjusted using the software
menu. The operating structure is split into settings for the home menu and settings
for the configuration menu. For standard applications, adjusting the ejector's
settings in the home menu will suffice. An advanced configuration menu is available
for applications with special requirements.
When settings are changed, undefined states may occur in the system for
short periods of time (for around 50 ms) under certain circumstances.
Vacuum display
Outside of the menus, the ejector is in display mode and displays the current
vacuum.
If there is overpressure in the vacuum circuit, the display "-FF" appears. This
normally occurs in the "Blow off" operating state.
If the vacuum value is too high (outside of the measurement range), the display "FFF"
appears.
Individual functions
In display mode, a particular function is assigned to each button.
Supply voltage
O To display the supply voltage currently applied to the ejector in volts, press the
button .
3 sec.
After 3 s, the display returns to the vacuum display.
The ejector is not a calibrated measurement device; however, the displayed
voltage can be used as a reference value and for comparative
measurements.
Operating mode display
O To display the current operating mode (SIO/Standard I/O mode or IO-Link mode),
press the button .
3 sec.
After 3 s, the display returns to the vacuum display.
For further information about IO-Link mode (R412026283) and an electronic device
description (IO Device Description, IODD), please visit our Media Center at
www.aventics.com/media-centre/
Use the search bar to search for: IO-Link (ECD-IV) or IODD
Status indicator
When an error occurs, it is displayed in the form of an error code ("E number") on the
display. The ejector's response to errors depends on the type of error.
A list of possible errors and the associated codes is provided under
Any operation taking place in the menu may be interrupted should an error occur.
Home menu
The home menu can be used to adjust and check all of the settings for the ejector's
standard applications.
*
>2 sec.
8/1
and
**
Switching point
>2 sec.
Air economizer function
Hysteresis
Air economizer function
Switching point
Parts control
Hysteresis
Parts control
Blow-off time, only active
with E-t or l-t
Calibration
>2 sec.
Vacuum sensor
** Setting parameters
** Parameter flashes as
confirmation
Adjusting parameters in the home menu
If the buttons or
scrolling quickly through the numbers to be changed.
If a value to be changed is canceled by briefly pressing the button
the value is not adopted.
To leave the home menu, press the button
1. To adjust the parameters in the home menu, briefly press button
2. To select the parameter you wish to change, press the button
3. To confirm the parameter, press the button
4. To change the parameter, press the button
5. To save the selected parameter, press the button
The parameter flashes as confirmation.
Adjusting the zero point (calibration)
1. To adjust the zero point of the built-in sensors, briefly press the button
2. Press the button or
3. To confirm the value, press the button
then as soon as the display [YES] appears, press the button
The parameter flashes as confirmation.
The vacuum sensor is now calibrated.

Configuration menu

An advanced configuration menu is available for applications with special
requirements. The operating structure appears as follows:
7/1 7/2
See fig. and
Adjusting the configuration menu
If the buttons or
scrolling quickly through the numbers to be changed.
If a value to be changed is canceled by briefly pressing the button
the value is not adopted.
To leave the configuration menu, press button
1. To adjust the parameters in the configuration menu, press the button
[-C-] during actuation.
2. To select the parameter you wish to change, press the button
3. To confirm the parameter, press the button
4. To change the parameter, press the button
5. To save the selected parameter, press the button
Entering the PIN code
1. To enter the PIN code, press the button
2. Press the button or
3. To confirm the menu item, press the button
4. Use the buttons or
5. To confirm the entry, press the button
6. Use the buttons or
7. To save the PIN code, press the button
[Loc] flashes in the display and the configuration menu disappears.
8/2
.
Running the "Reset to factory settings" function
1. To run the "Reset to factory settings" function, press the button
2. To select the menu item [rES], press the button
3. To confirm the selection of the menu item, press the button
then as soon as the display [YES] appears, press the button
The ejector has now been reset to the factory settings.
After confirmation, the display flashes for three seconds and then automatically
returns to display mode.
are pressed for around 3 s, the system starts
>2 s.
.
or .
>2 s.
until [CAL] appears in the display.
are pressed for around 3 s, the system starts
>2 s.
.
or .
>2 s.
>3 s.
to select the [Pin] menu item.
.
to enter the first number in the PIN code.
.
to enter the other numbers in the PIN code.
>2 s.
or .
16
,
.
or .
.
>2 s.
,
>3 s.
or .
>3 s.
>2 s.