Grass Cutting; Controls Description - GGP ITALY MCS 504 Serie Gebrauchsanweisung

46. Danger of cutting yourself. Cutting means. Do not put
hands or feet near or under the opening of the cut-
ting means.
47. Beware of hot surfaces!
OPERATING INSTRUCTIONS
For information on the engine and the battery (if sup-
plied), read the relevant owner manuals.
NOTE – The number which precedes each paragraph
links the references in the text to the respective illus-
trations (listed on page iii and following pages).
1. COMPLETE ASSEMBLY
NOTE The machine can be supplied with some parts al-
ready assembled.
WARNING! Unpacking and completing the assem-
bly should be done on a flat and stable surface, with
enough space for moving the machine and its packag-
ing, always making use of suitable equipment.
Disposal of the packaging should be done in accord-
ance with the local regulations in force.
1.1 Assembling the handle
• Model 474:
i - A ssemble one of the ends of the lower part of the han-
dle (1) using one of the two lower knobs and relative
screws (2), previously removed from their respec-
tive holes.
ii - S crew on the knob (2) to about half-way along the
screw thread.
iii - A ssemble the other end of the lower part of the han-
dle (1) and lock into position using the second lower
knob (2) and relative screws.
iv - F ully tighten the two knobs (2).
• Model 504:
– A ssemble the lower part of the handle (1) and secure
in place using the lower knobs (2), previously removed
from their respective holes.
Assemble the top part (3) using the knobs (4) and sup-
plied screws.
Fit the cable fasteners (5) as shown and secure the con-
trol cables.
• Manual ignition models
• Electric key ignition models
Fit the starter cable in the guide spiral (6) and tighten
the nut (7).
1.2 Battery connection
• Electric key ignition models
C onnect the battery cable to the general wiring connec-
tor on the lawnmower.
• Electric push-button ignition models
F ollow all the instructions provided in the engine
Instruction Manual.

2. CONTROLS DESCRIPTION

NOTE The meanings of the symbols on controls are ex-
plained in the previous pages.
2.1 Throttle lever
The throttle is controlled by the lever (1).
Lever positions are indicated on the relevant plate.
Some models have a fixed speed engine with no need for
a throttle.
2.2 Engine brake lever / cutting means
The cutting means brake is controlled by the lever (1) which
must be held against the handle during ignition and during
lawnmower operations.
The engine stops when the lever is released.
2.3 Drive lever (where applicable)
On power-driven models, push the lever (1) toward the han-
dle for forward movement.
The lawnmower stops moving forward when the lever is
released.
The engine must always be ignited with the drive disen-
gaged.
WARNING! To prevent damage to the transmis-
sion, do not pull the machine backwards with the trans-
mission engaged.
2.4 Converter control lever (if fitted)
In the models with drive systems, the converter control le-
ver (if fitted) allows the operator to regulate forward gear
speed.
To do so, move the lever (1) following the indications pro-
vided near the control lever.
IMPORTANT The engine must be running and the drive
engaged when switching from one speed to another.
Do not touch the converter control when the engine is
stopped. Doing this could damage the converter.
NOTE If the machine does not move forward with the le-
ver in the « » position, simply move the lever to «
then immediately return to the «
2.5 Cutting height adjustment
The cutting height is adjusted by the levers (1).
The four wheels must be adjusted to the same height.
DO THIS WHEN THE CUTTING MEANS IS STATIONARY.

3. GRASS CUTTING

3.1a Preparation for mowing and mulching
– O n models with side discharge: make sure that the side
discharge guard (1) is lowered.
3.1b Preparation for mowing and side discharge
of grass (if provided)
– L ift the side discharge guard (1) and fit the side discharge
chute (2) as illustrated in the diagram.
– Close the side discharge guard (1) so that the side dis-
charge chute (2) is locked in place.
3.2 Engine ignition
During ignition, follow the instructions in the engine manual
• Manual ignition models
P ull the cutting means brake lever (1) against the handle
and firmly tug the knob on the ignition cable (2).
• Electric key ignition models
P ull the cutting means brake lever (1) against the handle
4
» and
» position.