Controls Description; Routine Maintenance; Grass Cutting - GGP ITALY EPL 424 Serie Gebrauchsanweisung

1. COMPLETE ASSEMBLY
NOTE The machine can be supplied with some parts al-
ready assembled.
WARNING!
bly should be done on a flat and stable surface, with
enough space for moving the machine and its packag-
ing, always making use of suitable equipment.
Disposal of the packaging should be done in accord-
ance with the local regulations in force.
1.1 Assembling the handle
Insert the lower right (1) and left (2) parts of the handle into
the respective holes and fasten them in place with the sup-
plied screws (3) and the washers (4).
Attach the top of the handle (4) to the bottom parts using
the knobs (5) and the supplied nuts and bolts as shown.
Fit the starter cable (6) in the guide (7) and tighten the
nut (8).
Secure the control cables using the binder (9).
1.2 Assembling the grass catcher
Insert the frame (1) in the fabric section of the grass catcher
(2) and snap on all the plastic sections (3), using a screw-
driver as illustrated.
1.3 Battery connection
In electric ignition system models, connect the battery ca-
ble to the general wiring connector on the lawnmower.

2. CONTROLS DESCRIPTION

NOTE The meanings of the symbols on controls are ex-
plained in the previous pages.
2.1 Engine brake lever / cutting means
The cutting means brake is controlled by the lever (1) which
must be held against the handle during ignition and during
lawnmower operations.
The engine stops when the lever is released.
IMPORTANT The cutting means must stop within a few
seconds of when the lever is released; if you notice that more
time is required for it to stop, contact a Specialised Centre
immediately.
2.2 Drive lever (where applicable)
On power-driven models, push the lever (1) toward the han-
dle for forward movement.
The lawnmower stops moving forward when the lever is
released.
The engine must always be ignited with the drive disen-
gaged.
2.3 Cutting height adjustment
The cutting height is adjusted by the specific lever (1).
DO THIS WHEN THE CUTTING MEANS IS STATIONARY.

3. GRASS CUTTING

NOTE This machine can be used to mow lawns in a num-
ber of different ways; before starting work, prepare the ma-
chine based on how the lawn is to be mowed.
DO THIS WHEN THE ENGINE IS OFF.
Downloaded from www.Manualslib.com
Unpacking and completing the assem-
manuals search engine
3.1 Preparation for mowing and grass collection by
the grass catcher
Lift the rear discharge guard (1) and fasten the grass catch-
er (2) correctly as shown in the illustration.
3.2 Engine ignition
During ignition, follow the instructions in the engine man-
ual, then pull the cutting means brake lever (1) against the
handle and firmly tug the knob on the ignition cable (2).
3.3 Mowing the lawn
The appearance of the lawn will improve if you alternate
cutting in both directions at the same height.
When the grass catcher is too full, grass collection is no
longer efficient and the sound of the lawnmower changes.
To remove and empty the grass catcher,
– s top the engine and wait for the cutting means to stop;
– l ift the rear discharge guard, grasp the handle and re-
move the grass catcher keeping it in an erect position.
Lawn care recommendations
Each type of grass has different characteristics and may
thus require different ways of caring for the lawn; always
read the instructions on seed boxes for mowing height for
the growing conditions in the work area.
Keep in mind that most grass is made up of a stem and one
or more leaves. If leaves are fully cut, the lawn is damaged
and growth is more difficult.
The following indications generally apply:
– c utting too low tears and uproots the grass, giving it a
"spotted" appearance;
– i n the summer, cutting must be higher to prevent the
ground from drying;
– d o not cut wet grass; this could reduce cutting means ef-
ficiency due to sticky grass and tear the lawn.
– f or particularly high grass, initially mow at the maximum
height allowed by the machine then mow again after two
or three days.
3.4 End of operations
When work has been completed, release the brake lever
(1) and disconnect the spark plug cap (2).
WAIT UNTIL THE CUTTING MEANS STOPS before
proceeding any further.

4. ROUTINE MAINTENANCE

Store the lawnmower in a dry place.
IMPORTANT Routine and accurate maintenance is es-
sential in maintaining original machine safety and perfor-
mance levels.
Adjustments or maintenance operations must only be per-
formed with the engine switched off and the spark plug ca-
ble disconnected.
1) W ear strong protective gloves before cleaning, main-
taining or adjusting the machine.
2) A ccurately wash the machine with water after cutting;
remove grass debris and mud accumulated in the chas-
sis to prevent it from drying and causing problems the
next time the lawnmower is used.
3) I f accessing the lower part is necessary, only tilt the ma-
chine on the side indicated in the engine manual, follow-
ing the relevant instructions.
4