Changing The Oil In The Wheel Motors - Stiga TITAN Serie Gebrauchsanweisung

EN
9. Fill with new oil through the 3/8" return for
PTO, see fig. 1. Use a pump with 10 micron fil-
ter.
Oil: See 2.1.
Oil quantity when changing: See 2.1.
10.After filling the oil, start the engine and run the
machine for a few minutes and check for oil
leakage.
11.Check the oil level. See 3.5.11.
6.9 CHANGING THE OIL IN THE
WHEEL MOTORS
Change the oil in the gear housing of the wheel
motors as follows:
1. Operate the machine at varying workload for 5-
10 minutes in order to warm up the oil in the
wheel motors.
2. Place the machine on a level surface.
3. Clean carefully around the
oil plugs (12:V, W).
4. Place a container under the oil drain plug
(12:W), remove the plug and let the oil run out
into a container.
5. Remove the filler plug (12:V).
6. Install the oil drain plug.
Dispose of the oil according to local regulations.
7. Fill with new oil via the filler plug hole. Pump
in the oil with help of an oil can. Fill until the
level reach the the filler plug hole.
Regarding type and volume of oil, see the table
in 2.1.
8. Install the filler plug.
9. Tighten the plugs to 30 Nm.
6.10BELT TRANSMISSIONS
After 5 hours of operation check that all belts are
intact and not damaged.
6.11 CLEANING THE COOLING SYS-
TEM
All services should be carried out by authorised
workshops.
6.12 BATTERY (7:M)
Acid that comes into contact with eyes
or skin causes serious injury. If you
come into contact with acid,
immediately rinse with water and
contact a doctor.
The battery is a valve-regulated battery with 12 V
nominal voltage. The battery fluid does not need to
and cannot be checked or topped up. The only
maintenance that is required is charging, for exam-
ple after extended storage.
90
ENGLISH
The battery must be fully charged
before being used for the first time. The
battery must always be stored fully
charged. If the battery is stored while
discharged, serious damage will occur.
6.12.1 Charging with the engine
The battery can also be charged using the engine's
alternator as follows:
1. Install the battery in the machine as shown be-
low.
2. Place the machine outdoors or install an extrac-
tion device for the exhaust fumes.
3. Start the engine according to the instructions in
the user guide.
4. Allow the engine to run continuously for 45
minutes.
5. Stop the engine. The battery will now be fully
charged.
6.12.2 Charging using battery charger
When charging with the battery charger, a battery
charger with continuous voltage must be used.
Contact your dealer to purchase a battery charger
with constant voltage.
The battery can be damaged if a standard type
battery charger is used.
6.12.3 Removal/Installation
The current must be cut using the main
switch (1:F2) before disconnecting the
battery.
If the cables are interchanged, the
generator and the battery will be
damaged.
Tighten the cables securely. Loose
cables can cause a fire.
The engine must never be driven with
the battery disconnected. There is a risk
of serious damage to the alternator and
the electrical system.
Remove/install the battery as follows:
1. Cut the power using the main switch (1:F2).
2. Remove the left-hand engine cover.
3. Disconnect the battery's cable connections and
remove the battery.
4. Install the battery in reverse order. Connect the
red cable to the battery's positive terminal (+)
and the black cable to the battery's negative ter-
minal (-).
5. Activate the main switch.
6.12.4 Cleaning
If the battery terminals are coated with oxide, they
should be cleaned. Clean the battery terminals with
a wire brush and grease them using terminal
grease.
Original instructions for use