Stiga TITAN Serie Gebrauchsanweisung Seite 82

EN
3.4.4.2 Ignition lock (1:E2)
The ignition lock is used for starting and stopping
the engine.
Four positions:
Preheat position: The cylinders are heat-
ed to facilitate starting. Hold in this posi-
tion as below at lower temperatures before
starting the engine.
Max 5 seconds
Stop position: The engine is stopped. The
key can be removed.
Operating position: Bypassed at start-up
and used when the engine is running.
Start position: The electric starter motor
is activated when the key is turned to the
spring-loaded starting position. Once the
engine has started, let the key return to the
operating position.
3.4.4.3 Implement lifter (1:Ls)
This control controls both the hydraulic tool lift at
the front of the machine (1:L) and the lift cylinder
for tools installed under the cab. These are con-
nected in series.
The control (1:Ls) only works when the engine is
running.
However, it can be lowered to the floating position
when the engine is off.
Never leave the machine with the imple-
ment in the transport position. Risk of
serious crushing injuries by the imple-
ment as it lowers quickly if the control
is unintentionally affected.
The lever has the four following positions:
Floating position. Move the lever to its
front position, where it locks. The imple-
ment is now lowered to its floating posi-
tion.
In the floating position, the implement
always rests against the ground at the
same pressure and can follow the con-
tours of the ground.
Use the floating position when carrying
out work.
Lowering. The implement lowers re-
gardless of its weight. The lowering
force is determined by the implement's
weight and the hydraulic down force that
is applied when lowering.
Locking in the transport position. The
lever has returned to the neutral position
after raising and lowering. The imple-
ment is locked in the transport position.
82
ENGLISH
Raising. Move the lever to the rear posi-
tion until the implement is in the highest
position (transport position). Then re-
lease the lever to lock in the transport po-
sition.
3.4.4.4 Hydraulic control (1:Aux1s)
This control is used to control certain functions de-
pending on the attached implement.
The control only works when the engine is running
and the implement's hydraulic hoses for the in-
tended function are connected to the hydraulic out-
put (1:Aux1).
3.4.4.5 Hydraulic control (1:Aux2s)
This control is used to control certain functions de-
pending on the attached implement.
The control only works when the engine is running
and the implement's hydraulic hoses for the in-
tended function are connected as follows:
• Implement at the front via the hydraulic outputs
(1:Aux2f).
• Implement at the rear via the hydraulic output
(1:Aux2r).
See also 3.4.4.9
Both hydraulic outputs on the rear section are con-
nected in parallel.
3.4.4.6 Switch (1:Ss)
The switch can be used to smoothly set the
cutting height of the cutting deck with
electric cutting height adjustment.
The switch controls the contact (1:S) with
switching polarity.
3.4.4.7 Switch (1:PTOs)
A lever for engaging and disengaging the opera-
tion of the front mounted implement. Two posi-
tions:
1. Press the front part of the switch – PTO
engages. The symbol will light up.
2. Press the rear part of the switch – PTO
disengages.
To prevent unnecessary increases in pressure in
the hydraulic system, set the throttle control to
1/4 throttle before the hydraulic PTO is en-
gaged.
The control activates a valve that transfers the
power from the hydraulic pump to the front mount-
ed implement.
The power is then transferred hydraulically to the
tool via the hydraulic output at the front (1:PTO).
3.4.4.8 Switch (1:Ys)
The switch has three positions and can be
12V
used for the sand spreader for example.
The switch controls the contact (1:Y).
Original instructions for use