Synergic Curves Screen (Wf 4000 Smart) - voestalpine WF 4000 Smart Betriebsanweisung

27 Initial increment time
Lets you set the initial increment time. Lets you auto-
mate the "crater filler" function.
Minimum 0.1s, Maximum 99.9s, Default Off
28 Crater filler time
Lets you set the "crater filler" time. Lets you automate
the "crater filler" function.
Minimum 0.1s, Maximum 99.9s, Default Off
29 (Crater filler) slope
Allows you to set a gradual passage between the initial
wire speed (initial increment) and the final wire speed
(crater filler).
Parameter set in seconds (s).
Minimum 0.1s, Maximum 10.0s, Default off
30 Spot welding
Allows you to enable the "spot welding" process and
establish the welding time.
Minimum 0.1s, Maximum 25s, Default off
31 Pause point
Allows you to enable the "pause point" process and
establish the pause time between one welding opera-
tion and another.
Minimum 0.1s, Maximum 25s, Default off
202 Inductance
Allows electronic regulation of the series inductance of
the welding circuit.
Makes it possible to obtain a quicker or slower arc to
compensate for the welder's movements and for the
natural welding instability.
Low inductance = reactive arc (more spatter).
High inductance = less reactive arc (less spatter).
Minimum -30, Maximum +30, Default syn
330 Voltage
Lets you set welding voltage.
399 Welding speed
Lets you set welding speed.
Minimum 1cm/min, Maximum 500cm/min, Default
35cm/min (reference speed for manual welding)
500 Allows the selection of the required graphic interface:
XE (Easy Mode)
XA (Advanced Mode)
XP (Professional Mode)
Allows access to the higher set-up levels:
USER: user
SERV: service
vaBW:vaBW
551 Lock/unlock
Allows the locking of the panel controls and the inser-
tion of a protection code (consult the "Lock/unlock"
section).
552 Buzzer tone
Permits adjustment of the buzzer tone.
Minimum Off, Maximum 10, Default 10
601 Regulation step
Allows the regulation of a parameter with a step that
can be personalised by the operator.
Minimum 1, Maximum Imax, Default 1
602 External parameter CH1, CH2, CH3, CH4
Allows the management of external parameter (mini-
mum value, maximum value, default value, parameter
selected).
(Consult the "External controls management" section).
606 U/D torch
Allows the management of the external parameter
(CH1) (parameter selected).
705 Circuit resistance calibration
Lets you calibrate the system.
Press the encoder knob to access parameter 705.
Place the tip of the wire guide in electrical contact with
the work piece.
Press and hold the torch trigger for at least 1 s.
751 Current reading
Allow the real value of the welding current to be dis-
played.
Allows the welding current display method to be set
(consult the "Interface personalisation" section).
752 Voltage reading
Allows the real value of the welding voltage to be dis-
played.
Allows the welding voltage display method to be set
(consult the "Interface personalisation" section).
760 (Motor) Current reading
Allow the real value of the (motor) current to be dis-
played.
801 Guard limits
Allows the setting of the warning limits and of the guard
limits.
Allows the accurate control of the various welding
phases (consult the "Guard limits" section).
3.8 Synergic curves screen
(WF 4000 Smart)
1 General
Allows the selection of the required welding method.
Manual welding method
Allows the manual setting and regulation of
each individual welding parameter (MIG/MAG).
Synergic welding method
Makes it possible to use a series of pre-settings
( s y n e r - gic curves) available in the memory
of the system.
T h e changing and correction of the ini-
t i a l settings proposed by the system is
allowed.
1
It allows the selection of:
synergic MIG
manual MIG
47