Transport; Storage; Care And Maintenance - Kärcher B 150 R Betriebsanleitung

 Press Info button - the set value blinks.
 Set the desired value by turning the info
button.
 Press Info button.
Setting the language
 Turn the info button until "Language" is
displayed.
 Press Info button.
 Turn the info button until the desired
language is highlighted.
 Press Info button.
Factory setting
The factory settings of all parameters are
restored.
Cleaning Programs
Parameters that are adjusted with the grey
Intelligent Key, are kept until another set-
ting is selected.
 Turn the program selection switch to
the desired cleaning program.
 Press the info button - the first adjusta-
ble parameter is displayed.
 Press Info button - the set value blinks.
 Set the desired value by turning the info
button.
 Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10
seconds.
 Select the next parameter by turning
the Info button.
 After all desired parameters have been
modified, turn the info button until "Exit
menu" is displayed.
 Press the info button - you will exit the
menu.

Transport

DANGER
Risk of injury! When loading or unloading
the appliance, it may only be operated on
gradients of max. 10% (Adv 15%). Drive
slowly.
CAUTION
Risk of injury and damage! Observe the
weight of the appliance when you transport
it.
 When transporting in vehicles, secure
the appliance according to the guide-
lines from slipping and tipping over.
With mounted D cleaning head
 Remove brushes from the brush head.
24

Storage

CAUTION
Risk of injury and damage! Note the weight
of the appliance in case of storage.
 This appliance must only be stored in
interior rooms.
 Select the storage site for the appliance
taking into consideration the permissi-
ble total weight of the appliance in order
not to impact its stability.

Care and maintenance

DANGER
Risk of injury! Before working on the appli-
ance, remove the Intelligent Key and the
mains plug of the charger.
Pull out the battery plug.
 Drain and dispose of the dirt water and
the residual fresh water.
CAUTION
Risk of injury due to overrun of the suction
turbine.
Suction turbine will continue to run for a
while after switch-off. Carry out mainte-
nance tasks only after the suction turbine
has come to a halt.
Maintenance schedule
After the work
ATTENTION
Risk of damage. Do not sluice the appli-
ance with water and do not use aggressive
detergents.
 Drain off dirt water.
 Clean protective turbine strainer.
 Only with R cleaning head Remove bulk
waste container and empty it.
 Clean the outside of the appliance with
a damp cloth which has been soaked in
mild detergent.
 Clean the vacuum lips and the wiping
lips, check for wear and replace if re-
quired.
 Check the brushes for wear, replace if
required.
 Charge battery.
Monthly
 During long operating pauses: Carry
out refill charging for the battery.
 Check battery poles for oxidation, brush
off if necessary. Ensure firm seating of
the connection cable.
 Clean the seals between waste water
tank and cover and check for tightness,
replace if required.
 Check the acid density of the cells if the
batteries are not maintenance-free bat-
teries.
 Clean the brush tunnel (only R cleaning
head)
8
-
EN
 Remove the water distribution strip from
the cleaning head and clean water ca-
nal (only R cleaning head).
Yearly
 Have the prescribed inspection carried
out by the customer service.
Reset the counter
When a maintenance task indicated in the
display has been performed, the relevant
maintenance counter must be reset after-
wards.
 Plug in the Intelligent Key.
 Bring the safety switch into the "1" posi-
tion.
 Set programme selector switch to trans-
port run.
 Press Info button.
 Turn the info button until "Maintenance
counter" is displayed.
 Press Info button.
The counter readings are displayed.
 Press Info button.
"Delete counter" is indicated.
 Turn the info button until the counter to
be deleted is highlighted.
 Press Info button.
 Select "YES" by turning the info button.
 Press Info button.
The counter is deleted.
Note:
The service counter can only be reset by
the customer service.
The service counter indicates the time until
the next service by the customer service is
due.
Maintenance Works
Maintenance contract
To ensure a reliable operation of the appli-
ance maintenance contracts can be con-
cluded with the competent Kärcher sales
office.
Cleaning the protective turbine strainer
 Open the cover of the waste water tank.
 Squeeze the locking hooks.
 Pull off the float.