Benning it100 Bedienungsanleitung Seite 14
Vorschau ausblenden
Andere Handbücher für it100:
- Bedienungsanleitung (73 Seiten) ,
- Bedienungsanleitung (42 Seiten)
Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
2. Safetynote
The instrument is built and tested in accordance with
DIN VDE 0411 part 1/ EN 61010 part 1
DIN VDE 0413 part 1, 2 and 4/ EN61557 part 1, 2 and 4 and has left the factory
in perfectly safe technical state. To maintain this state and ensure safe operation
of the appliance tester, the user must observe the notes and warnings given in
these instructions at all times.
The instrument may be used only in electrical circuits in the
overvoltagecategoryIIwithmaximumvoltage1000Vbetween
theconductorandground,orinelectricalcircuitsintheover-
voltage category III with 600 V between the conductor and
ground. Remember that work on electrical components of all
kindsisdangerous.Evenlowvoltagesof30VACand60VDC
maybedangeroustohumanlife.Asfromaninputvoltageof
30VAC/DCthewarningsymbol" "appearsinthedisplayof
the BENNINGIT100, as warning that a dangerous voltage is
connected.
Beforestartingtheappliancetesterup,alwayscheckitaswell
asallcablesandwiresforsignsofdamage.
Important! During the insulation resistance measurement,
dangerouslevelsofvoltagemayoccurintheBENNINGIT100.
Should it appear that safe operation of the appliance tester is no longer possible,
it should be shut down immediately and secured to prevent it being switched
on accidentally.
It must be assumed that safe operation is no longer possible
- if the instrument or the measuring cables show visible signs of damage, or
- if the appliance tester no longer functions, or
- after long periods of storage under unfavourable conditions, or
- after being subjected to rough transportation.
Inordertoavoiddanger,
- donottouchthebareprodtipsofthemeasuringcables
- plug the measuring cables into the correspondingly
designated measuring sockets on the BENNINGIT100
(seeFig.2:Inputsockets)
- when disconnecting the measuring circuit always first
disconnect the voltage carrying measuring cable (phase
line)andthereafterdisconnectthezeromeasuringline.
- do not operate the BENNINGIT100 in the vicinity of
explosivegasesordust.
3. Deliveryscope
The scope of delivery for the BENNING IT 100 comprises:
3.1 One BENNING IT 100
3.2 One safety measuring cable, red (L = 1.2 m; prod tip diameter = 4 mm)
3.3 One safety measuring cable, black (L = 1.2 m; prod tip diameter = 4 mm)
3.4 One safety alligator clip, red, 4 mm plug-in system
3.5 One safety alligator clip, black, 4 mm plug-in system
3.6 One compact protective pouch
3.7 S ix Mignon monocells 1.5 V according to IEC/ DIN R6/ LR6 and one
fuse (fitted in unit as first equipment),
3.8 One operating instructions manual
Parts subject to wear:
- T he BENNING IT 100 contains a fuse as protection against overload:
One fuse, nominal current rating 0.5 A, 1000 V AC/ DC, 10 kA, quick blow,
D = 6.3 mm, L = 32 mm.
- T he BENNING IT 100 is powered by six Mignon monocells 1.5 V according
to IEC/ DIN R6/ LR6.
4. Descriptionoftheappliancetester
See Fig. 1:
11/ 2006
Front side of the instrument
BENNING IT 100
Werbung
Inhaltsverzeichnis
