Before Starting The Machine; General Information - Parkside PDS 120 A1 Originalbetriebsanleitung

Max. cutting height at 90°:
Max. cutting height at 45°:
minimum size work piece wxh:
maximum size work piece wxh:
Weight:
Operating mode S6 30%:
Continuous operation with idling (cycle time 10 minutes). To
ensure that the motor does not become excessively hot, it
may only be operated for 30% of the cycle at the specified
rating and must then be allowed to idle for 70% of the cycle.
Noise emission values
Sound
Sound values were measured in accordance with EN 61029.
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Sound pressure level L : 66.9 dB(A)
pA
Uncertainty K : 3 dB(A)
pA
Sound power level L : 79.9 dB(A)
WA
Uncertainty K : 3 dB(A)
WA
The quoted values are emission values and not necessarily
reliable workplace values. Although there is a correlation
between emission and immission levels it is impossible to
draw any certain conclusions as to the need for additional
precautions. Factors with a potential influence on the actual
immission level at the workplace include the duration of
impact, the type of room, and other sources of noise etc., e.g.
the number of machines and other neighboring operations.
Reliable workplace values may also vary from country to
country. With this information the user should at least be
able to make a better assessment of the dangers and risks
involved.
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.

7. Before starting the machine

Important.
Always pull out the power plug before making adjust-
ments to the equipment.

7.1 General information

• All covers and safety devices have to be properly fitted
before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed before,
watch out for foreign bodies such as nails or screws, etc.
• Before you actuate the On/Off switch, make sure that the
saw blade is correctly fitted and that the equipment's mov-
ing parts run smoothly.
11 GB
50 mm
22 mm
100 x 22 mm
400 x 50 mm
12.7 kg
• Check that the voltage on the rating plate is the same as
your supply voltage before you connect the equipment to
the power supply.
• Only ever connect the equipment to a properly installed
shock-proof socket which is protected by a 10A fuse as a
minimum.
7.2 Installing the fretsaw on a workbench
(Fig. 3, 4)
The unit may only be installed by a professional.
Required for installing (not provided):
• M6 hex screw (4x)
• M6 hex nut (8x)
• Washer, Ø 7 mm (4x)
• Flat gasket, Ø 7 mm (4x)
• Rubber base: 410 x 255 x 13 mm
The length of the screws to be used varies, depending on the
thickness of the table top.
• Install the fretsaw on a work table made from solid wood.
This will avoid excessive noise caused by vibrations.
• Mark the drill holes. Use the fretsaw as a template for this
purpose.
• Drill 4 holes with a diameter of 9 mm into the work table
and the rubber base.
• Screw the fretsaw to the table using the mounting points
(Fig. 3 Item 16) and in the following sequence (Fig. 4):
A) Fretsaw
B) Rubber base
C) Work table
D) Flat gasket
E) Washer
F) Hex nut
G) Hex nut
H) Hex screw
• Tighten the hex nut (F) and secure it with a second hex nut
(G).
7.3 Assembly
Important! Always pull out the power plug before carrying
out any maintenance or conversion work on the fretsaw.
7.3.1 Mounting the saw blade guard and the
sawdust blower facility (Fig. 6/7/8)
• Attention: Prior to the installation of the retaining device
(18), the pre-assembled saw blade (17) must be disman-
tled as described in articel 7.3.2.
• Secure the retaining device (29) to the machine by using
the knurled screw (3). Attach the retaining device (18) to
the bracket (29), as shown in the figure.
• Secure the saw blade guard (5) with the nut and bolt.
• Mount the blow-off device (1) as shown in Figure 8.