Residual Risks; Before Starting The Equipment; Attachment And Operation - Parkside PKZS 2000 A1 Bedienungs- Und Sicherheitshinweise

The work piece must have a minimum height of 3mm
and a minimum width of 10 mm.
Make sure that the workpiece is always secured with
the clamping device.
Noise
Total noise values determined in accordance with EN 61029.
Sound pressure level L ................................. 91,9 dB(A)
pA
Uncertainty K ...........................................................3 dB
pA
Sound power level L ................................. 104,9 dB(A)
WA
Uncertainty K .........................................................3 dB
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing

Residual risks

The machine has been built according to the state of the
art and the recognised technical safety requirements.
However, individual residual risks can arise during op-
eration.
• Health hazard due to electrical power, with the use of im-
proper electrical connection cables.
• Furthermore, despite all precautions having been met,
some non- obvious residual risks may still remain.
• Residual risks can be minimised if the „safety instructions"
and the „Proper use" are observed along with the whole
of the operating instructions.
• Do not load the machine unnecessarily: excessive pres-
sure when sawing will quickly damage the saw blade,
which results in reduced output of the machine in the pro-
cessing and in cut precision.
• When cutting plastic material, please always use clamps:
the parts which should be cut must always be fixed be-
tween the clamps.
• Avoid accidental starting of the machine: the operating
button may not be pressed when inserting the plug in an
outlet.
• Use the tool that is recommended in this manual. In doing
so, your machine provides optimal performance.
• Hands may never enter the processing zone when the ma-
chine is in operation.
• Release the handle button and switch off the machine
prior to any operations

7. Before starting the equipment

• The equipment must be set up where it can stand securely.
Secure the machine on a workbench or a stand with 4
screws through the holes in the fixed saw table (15).
• All covers and safety devices have to be properly fitted
before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed before,
watch out for foreign bodies such as nails or screws, etc.
• Before you press the ON/OFF switch check that the saw
blade is fitted correctly. Moving parts must run smoothly.
• Before you connect the equipment to the power supply
make sure the data on the rating plate are dentical to the
mains data.
20 GB/IE

8. Attachment and operation

8.1 Attaching the Crosscut, drag and mitre Saw
(Fig. 1/2/3/4/5)
• In order to adjust the rotary table (14) loosen the set screw
(26) approx. 2 turns.
• Turn the rotary table (14) and pointer (12) to the desired
angle measurement on the scale (13) and secure with the
set screw (26).
• Pressing the machine head (4) lightly downwards and re-
moving the locking bolt (23) from the motor bracket at the
same time disengages the saw from the lowest position.
• Swing the machine head (4) up until the release lever (3)
latches into place.
• It is possible to secure the clamping devices (7) to the left
or right on the stationary saw bench (15). Insert the clamp-
ing devices (7) in the holes on the rear side of the stop rail
(16) and secure it with the star grip screws (7a).
• Attach the workpiece supports (8) to the fixed saw table
as shown in Figure 5 and fasten with the screw (9).
• It is possible to tilt the machine head (4) a max. 45° to the
left by loosening the set screw (22).
8.2 Precision adjustment of the stop for crosscut 90°
(Fig. 1/6/7)
• No stop angle included.
• Lower the machine head (4) and secure using the locking
bolt (23).
• Loosen the set screw (22).
• Position the angle stop (a) between the saw blade (6) and
the rotary table (14).
• Adjust the adjusting screw (27) until the angle between the
saw blade (6) and rotary table (14) is 90°.
• It is not necessary to fix this setting because it is maintained
by the spring pretension.
• Subsequently check the position of the angle indicator. If
necessary loosen the pointer (19) using a Philips screw-
driver, set to position 0° on the angle scale (18) and re-
tighten the retaining screw.
8.3 Cross cut 90° and turntable 0° (Fig. 8)
In the case of cutting widths up to approx. 100 mm it is pos-
sible to fix the traction function of the saw with the set screw
(20) in the rear position. In this position the machine can be
operated in cross cutting mode.
If the cutting width is over 100 mm then it is necessary to
ensure that the set screw (20) is loose and the machine head
(4) can move.
Attention! For 90° cross cuts, the moveable stop rail (16a)
must be fixed in the inner position.
• Open the set screw (16b) on the moveable stop rail (16a)
and push the moveable stop rail (16a) inwards.
• The moveable stop rail (16a) must be locked in a position
far enough from the inner position that the distance be-
tween the stop rail (16a) and the saw blade (6) is no more
than 8 mm.
• Before making the cut, check that no collision could occur
between the stop rail (16a) and the saw blade (6).
• Tighten the set screw (16b) again.
• Move the machine head (4) to its upper position.