Intended Purpose - Eufab BIKE TWO Bedienungsanleitung

Rear rack BIKE TWO for trailer coupling, for 2 bicycles with EU operating permit
OVERVIEW

1. INTENDED PURPOSE

2. SPECIFICATIONS
3. SAFETY NOTES AND IMPORTANT INFORMATION
4. OPERATING INSTRUCTIONS
4.1 MOUNTING THE BICYCLE RACK
4.2 MOUNTING THE BICYCLE RACK ON THE TRAILER TOW BAR
4.3 MOUNTING THE BICYCLES TO THE CARRIER
5. MAINTENANCE
6. NOTES REGARDING ENVIRONMENTAL PROTECTION
7. CONTACT INFORMATION
WARNING
Please read the operating instructions carefully prior to use and observe all safety instructions!
Retain the original packaging, the proof of purchase as well as these instructions for subsequent reference!
Non-compliance can lead to personal injuries, damage to the device or your property!
Please check content of package for integrity and completeness prior to use!
1. INTENDED PURPOSE
Transportation of two bicycles on the trailer coupling.
2. SPECIFICATIONS
Not suitable for use with aluminium trailer couplings
D-value of the trailer coupling must be at least 7.6 kN
Size (L x W x H): approx. 147 x 70 x 44 cm
Weight: 15 kg
Maximum payload: 35 kg (with a permitted supporting load of 50 kg)
40 kg (with a permitted supporting load of 60 kg)
40 kg (with a permitted supporting load of )
3. SAFETY NOTES AND IMPORTANT INFORMATION
• The ball surface of the trailer coupling must be clean, grease-free and free from any paint.
• The bicycle rack will only be seated properly on the coupling when secured and driven for a few kilometres. For this reason, check the fixture again for correct seat
and adjust the fixture if necessary.
• Check the bicycle rack for damages before use. Damaged or worn parts must be replaced immediately. Only original replacement parts may be used.
• Modifications to the bicycle rack are generally not permitted (mechanical or electrical). This can be very dangerous. Guarantee claims will no longer be accepted
and we can no longer guarantee the correct functioning of the bicycle rack if modifications have been made. We are not liable for any damages caused as a result of
incorrect installation, operation or modification.
• Check the lighting of your bicycle rack regularly to ensure correct functioning.
• Make sure that the bicycles are always secured using the frame holder and the wheel tensioning straps. The frame holder should be closed during transportation.
• Make sure that no parts of the bicycle can be lost (batteries, e-bike battery packs, bicycle pump, tachometer, baskets, saddles etc.). Remove
• these parts before transporting the bicycle!
• Check all tensioning straps and holders of the bicycle rack for secure seating and tighten if required.
• Do not cover the bicycles using tarpaulins, covers or similar.
• The bicycle rack will affect the behaviour of your vehicle. Adapt your driving speed to these circumstances (maximum of 130 km/h). Avoid sudden steering and control
motions.
• When reversing, remember that your vehicle is longer than it would normally be!
• The legal regulations and directives for the transportation of goods on your vehicle apply.
• If your vehicle has a parking assistant, the mounted bicycle rack may result in faulty operation. Deactivate the parking assistant function when the bicycle rack is
mounted.
• If your vehicle is fitted with a tailgate that opens automatically, this should be deactivate or only opened manually when the bicycle rack is mounted
• Remove the bicycle rack before using a car wash.
• The bicycle rack is designed for use on rough terrain.
• If the bicycle rack is not in use, remove the rack from the coupling.
The general operating permit must be carried in the vehicle when the rack is mounted.
Do not travel with the bicycle rack empty. Store it in the boot of your vehicle. This prevents increased fuel consumption and protects
the rack.
The driver is always responsible for ensuring that the load and the load securing meet the regulations.
4. OPERATING INSTRUCTIONS
4.1 MOUNTING THE BICYCLE RACK
Place the left and right halves of the rack table on an even surface with the wheel rail openings facing upwards. Secure the rack traverse to the rack table by feeding the M6
x 70 lock screws from the top through the table and traverse and screwing into from below with washers and nuts. At this point, do not yet tighten the nuts.
5
5
5
5
5
7
7
8
8
8
5