Standard Accessories - Hitachi CJ 110VA Bedienungsanleitung

SPECIFICATIONS
Voltage (by areas)*
Power Input*
Max. Cutting Depth
No-Load Speed
Stroke
Min. Cutting Radius
Weight (without cord)
*Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Blades (No. 41, No. 42, No. 46) ................ 1 each
Refer to Table 1 for use of the blades.
(2) Hexagon bar wrench ............................................... 1
(3) Splinter guard ........................................................... 1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES ... Sold separately
(1) Various types of blades
Refer to Table 1 for use of the blades.
(2) Dust collecter
(3) Rectilinear guide
(4) Circular guide
(5) Bench stand (Model TR12-B)
Optional accessories are subject to change without notice.
APPLICATIONS
Cutting various lumber and pocket cutting
Cutting mild steel plate, aluminum plate, and copper
plate
Cutting synthetic resins, such as phenol resin and
vinyl chloride
Cutting thin and soft construction materials
Cutting stainless steel plate (with No. 95, No. 96
or No. 97 blade).
PRIOR TO OPPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Mounting the blade
(1) Open the chip cover. (Fig. 1)
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
570W
Wood 100 mm
Mild Steel 10 mm
700—3200/min.
26 mm
25 mm
2.4kg
(2) Use the accessory hexagonal bar wrench to loosen
the blade set screw on the set ring, as shown in
Fig. 2.
(3) Fully insert the blade mounting portion into the set
ring with the rear face of the blade engaged with
the groove and tighten the set screw. (Fig. 2).
(4) Close the chip cover. (Fig. 1).
NOTE:
Loosened set screw may cause the blade to be
damaged. Always ensure that the set screw is
securely tightened. Always ensure that the mounting
portion of the set ring is clean and claer of sawdust
to ensure proper blade mounting and set screw
clamping.
5. Adjusting the blade operating speed
The CJ110VA is equipped with the electric control
circuit which enables stepless speed control. To
adjust the speed, turn the dial shown in Fig. 3.
When the dial is set to "1", the jig saw operates
at the minimum speed (700 /min). When the dial
set to "5", the jig saw operates at the maximum
speed (3200 /min). Adjust the speed according to
the material to be cut and working efficiency.
CAUTION
At low speed (dial setting: 1 or 2) do not cut a wood
with a thickness of more than 10 mm or metal with
a thickness of more than 1 mm.
6. Adjusting the orbital operation
(1) This machine employs orbital operation which moves
the blade back and forth, as well as up and down.
Set the change knob shown in Fig. 4 to "0" to
eliminate the orbital operation (the blade moves
only up and down). The orbital operation can be
selected in 4 steps from "0" to "III".
(2) For the hard material, such as a steel plate, etc.,
decrease the o3rbital operation. For the soft material,
such as lumber, plastic, etc., increase the orbital
operation to increase work efficiency. To cut the
material accurately, decrease the orbital operation.
7. Cutting stainless steel plates
The CJ110VA model, when used with the No. 95,
No. 96 or No. 97 blade, can cut stainless steel
plates. Carefully read "Concerning cutting of stainless
steel plates" for proper operation.
8. Splinter guard
Using the splinter guard when cutting wood
materials will reduce splintering of cut surfaces.
Insert the splinter guard in the space between the
base and sub-base, push forward and attach (see
Fig. 5).
English
5