Herunterladen Inhalt Inhalt Diese Seite drucken

Standard Accessories; Maintenance And Inspection - Hitachi CJ 160V Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 7
English

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the
accessories listed in the below.
○ Blades (No. 41, No. 42, No. 123X) ......................1 each
No. 41: Refer to Table 1
No. 42: Same with No. 12 (Table 1)
No. 123X: Mild steel plate 1.5 – 10 mm
○ Sub base .......................................................................1
○ Hexagon bar wrench .....................................................1
○ Splinter guard................................................................1
○ Dust collector ................................................................1
○ Chip cover .....................................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
○ Cutting various lumber and pocket cutting
○ Cutting mild steel plate, aluminum plate, and copper
plate
○ Cutting synthetic resins, such as phenol resin and vinyl
chloride
○ Cutting thin and soft construction materials
○ Cutting stainless steel plate (with No. 97 blade)
SPECIFICATIONS
Voltage (by areas)*1
Power Input*1
Max. cutting depth
No-load speed*1
Stroke
Min. cutting radius
Weight*2
*1 Be sure to check the nameplate on product as it is
subject to change by areas.
*2 Weight: According to EPTA-Procedure 01/2003
NOTE
Due to HITACHI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action
Changing blades
Adjusting the blade operating
speed*1
Switch operation
How to use the LED light
Adjusting the orbital operation
Splinter guard
Sub base*2
Chip cover
Housing the hexagonal bar wrench
Mounting the guide
Rectilinear cutting
(110 V, 120 V, 220 V, 230 V,
240 V)
800 W
Wood 160 mm
Mild steel 10 mm
800 – 2800 min
-1
26 mm
25 mm
2.5 kg
Figure
Page
124
2
124
3
125
4
125
5
125
6
125
7
126
8
126
9
126
10
126
11
126
12
Cutting a circle or a circular arc
Cutting metallic materials
Angular cutting
Pocket cutting
Concerning cutting of stainless steel
plates
Connecting with cleaner
Selecting accessories
*1 The tool is equipped with two modes: "Standard Mode"
and "AUTO Mode".
(1) Standard Mode
You can change the blade operating speed between
800 to 2800 min
(2) AUTO Mode
Depending on the workload, AUTO Mode "A" will
automatically change the blade operating speed
to 1400 min
or 2800 min
-1
lowering vibration and noise prior to and during
operation.
Adjust the dial for the mode and speed that best suits
your task conditions and materials.
Blade operating speed
Mode
Standard Mode
AUTO Mode
With AUTO Mode, the vibration frequency may not
reach 2800 min
or return to 1400 min
-1
variables such as the type of work.
NOTE*2
When the sub base is attached, the blade's protrusion
from the material being cut will be reduced by 3mm.
When the blade has been moved down to the lowest
point, check to make sure that it is protruding from the
material.
SELECTION OF BLADES
Accessory blades
To ensure maximum operating effi ciency and results, it is
very important to select the appropriate blade best suited to
the type and thickness of the material to be cut. Three types
of blades are provided as standard accessories. The blade
number is engraved in the vicinity of the mounting portion
of each blade. Select appropriate blades by referring to
Table 1.

MAINTENANCE AND INSPECTION

1. Inspecting the blade
Continued use of a dull or damaged blade will result in
reduced cutting effi ciency and may cause overloading of
the motor. Replace the blade with a new one as soon as
excessive abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4
13
14
15
16
17
18
by adjusting the dial from "1" to "5".
-1
. This has the eff ect of
-1
Dial
Blade operating speed
1 – 5
800 – 2800 min
No load: 1400 min
A
With load: 2800 min
depending on
-1
126
127
127
127
128
128
129
-1
-1
-1

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Cj 160va

Inhaltsverzeichnis