Operating The Product; Manual Controls - Dimplex CAS500R Bedienungsanleitung

Multiple Product Installation
Follow steps 1-4 in "Installing the Product into Surround/Enclosure" to fit the first product. It is important that the first
product is orientated so that the side of the product with the slots is left free and not connected to first end of the
installation (Fig 18).
1. When the first product is installed and securely fixed, prepare the second product by unscrewing the joining screws
(Fig 19A) and screwing them into the opposite side of the metalwork (Fig 19B). Please note, these screws should
not be fully tightened and 5-10mm of thread should be left protruding from the edge of the product.
2. Fit the second product beside the first product, ensuring the protruding screws of the second product engage with
slots of the first product. (Fig 20)
3. Ensure the second product is at the correct height to match the first product and ensure it is adequately level. This
can be done by adjusting the adjustable feet with a flat head screwdriver. (Fig 8) The levelness of the product can
be verified by checking the on-board level (Fig 9)
4. Tighten the screws of the second product so that it joins tightly with the first product.
Additional products can be fitted to the second product by following steps 1-4 above.

Operating the Product

This section describes how to activate your fire using either the manual controls or remote control.

MANUAL CONTROLS

The manual controls are located beneath the fuel bed. (Fig 21)
CAS500R
Mains Switch - Controls the electricity supply to the appliance. (Fig 21A)
Note: This switch must be in the 'ON' ( I ) position for the appliance to operate
Button Panel - Controls the functioning of the appliance. (Fig 21B)
• is the on/standby button. Press it to turn on and off the flame effect. Turning it on will be indicated by a single
beep and the main LED lights activating. Be careful not to look directly into the LED's as they can be very bright.
Although the main LED lights operate immediately, a further 45 seconds of warm up time is required before the
flame effect starts.
• is the Pairing button. This will pair your remote control to the receiver. See 'Remote Control Operation' for details.
• is the test mode button. This will be used by the manufacturer and the Service Engineer.
• is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible beep
when you reach the minimum level.
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level.
• is the reduce fire crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off. You will hear an audible beep when you reach the minimum level
• is the increase fire crackling sound. Press this to increase the volume of the crackling sound.You will hear an
audible beep when you reach the maximum level.
CAS1000R
Mains Switch - Controls the electricity supply to the appliance. (Fig 21A)
Note: This switch must be in the 'ON' ( I ) position for the appliance to operate
Button Panel 'C' Controls the functioning of the left side of product while Button Panel 'D' controls the functioning of the
right side of the product. Please note the flame height and fire crackling noise can be controlled independently on each
individual side of the product.
• is the on/standby button. Press it to turn on and off the flame effect. Turning it on will be indicated by a single
beep and the main LED lights activating. Be careful not to look directly into the LED's as they can be very bright.
Although the main LED lights operate immediately, a further 45 seconds of warm up time is required before the
flame effect starts.
• is the pairing button. This will pair your remote control to the receiver. See 'Remote Control Operation' for details.
• is the test mode button. This will be used by the manufacturer and the Service Engineer.
• is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible beep
when you reach the minimum level
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level.
• is the reduce fire crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off. You will hear an audible beep when you reach the minimum level.
• is the increase fire crackling sound. Press this to increase the volume of the crackling sound. You will hear an
audible beep when you reach the maximum level.
4