Technical Data - Scheppach SC40P Originalbetriebsanleitung

3 Keep grounded conductive objects, such as
tools, away from exposed, live electrical parts
and connections to avoid sparking or arcing.
These events could ignite fumes or vapors.
4 Always stop the engine and allow it to cool before
filling the fuel tank. Never remove the cap of the
fuel tank or add fuel while the engine is running
or when the engine is hot. Do not operate the ma-
chine with known leaks in the fuel system.
5 Loose the fuel tank cap slowly to relieve any
pressure in the tank.
6 Never over fill fuel tank. Fill tank to no more than
12.5mm (1/2" below the bottom of the filler neck
to provide space for expansion as the heat of the
engine can cause fuel to expand).
7 Replace all fuel tank and container caps securely
and wipe up spilled fuel. Never operate the unit
without the fuel cap securely in place.
8 Avoid creating a source of ignition for spilled fuel.
If fuel is spilled, do not attempt to start the en-
gine but move the machine away from the area of
spillage and avoid creating any source of ignition
until fuel vapors have dissipated.
9 Store fuel in containers specifically designed and
approved for this purpose.
10 Store fuel in a cool, well-ventilated area, safely
away from sparks, open flames or other sources
of ignition.
11 Never store fuel or machine with fuel in the tank
inside a building where fumes may reach a spark,
open flame, or other sources of ignition, such as
a water heater, furnace, clothes dryer and the
like. Allow the engine to cool before storing in
any enclosure.
Instructions for use and maintenance of the
machine
1 Never pick up or carry a machine while the en-
gine is running.
2 Do not force the machine. Use the correct ma-
chine for your application. The correct machine
will do the job better and safer at the rate for
which it was designed.
3 Do not change the engine governor settings GB
or over-speed the engine. The governor controls
the maximum safe operating speed of the engine.
4 Do not run the engine at a high speed when you
are not tilling.
5 Do not put hands or feet near rotating parts
6 Avoid contact with hot fuel, oil, exhaust fumes
and hot surfaces. Do not touch the engine or
muffler. These parts get extremely hot from op-
eration. They remain hot for a short time after you
turn off the unit. Allow the engine to cool before
doing maintenance or making adjustments.
7 If the machine should start to make an unusual
noise or vibration, immediately shut off the en-
gine, disconnect the spark plug wire, and check
for the cause. Unusual noise or vibration is gen-
erally warning of trouble.
8 Use only attachments and accessories approved
by the manufacturer. Failure to do so can result
in personal injury.
9 Maintain the machine. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the ma-
chine's operation. If damaged, have the machine
repaired before use. Many accidents are caused
by poorly maintained equipment.
10 Keep the engine and muffler free of grass,
leaves, excessive grease or carbon build up to
reduce the chance of a fire hazard.
11 Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
12 Never douse or squirt the unit with water or any
other liquid. Keep handles dry, clean and free
from debris. Clean after each use.
13 Observe proper disposal laws and regulations for
gas, oil, etc. to protect the environment.
14 Store idle machine out of the reach of children
and do not allow persons unfamiliar with the ma-
chine or these instructions to operate it. Machine
is dangerous in the hands of untrained users.
Instructions for maintenance
Before cleaning, repair, inspecting, or adjusting, shut
off the engine and make certain all moving parts have
stopped. Disconnect the spark plug wire, and keep the
wire away from the plug to prevent accidental starting.
Have your machine serviced by qualified repair person-
nel using only identical replacement parts. This will en-
sure that the safety of the machine maintained.

Technical data

Engine type
Displaycement
Max. engine output
Working speed
Fuel
Tank capacity
Engine oil
Tank capacity /oil
spark plug
Depth setting
Working width
Number of blades
Blade diameter
Collection bag capacity
Weight
Subject to technical changes!
Information concerning noise emission measured
according to relevant standards:
1-cylinder; 4 - stroke
118 cm³
2,2 kw
3600 rpm
unleaded fuel
2,5 l
10W 30 / SAE 30
0.6 L
LG F6TC
+5 / -15
400 mm
18
160 mm
45L
31 kg
GB 17