Introduction; Device Description; Scope Of Delivery; Intended Use - Scheppach MTE370 Bedienungsanleitung

1. Introduction

MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
WE RECOMMEND:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture.
Read the instruction manual each time before op-
erating the machine and carefully follow its informa-
tion. The machine can only be operated by persons
who were instructed concerning the operation of the
machine and who are informed about the associated
dangers. The minimum age requirement must be
complied with. In addition to the safety notices con-
tained in this operating manual and the particular in-
structions for your country, the generally recognised
technical regulations for the operation of identical de-
vices must be complied with.
We cannot accept any liability for damage or acci-
dents which arise due to a failure to follow these in-
structions and the safety instructions.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
2. Device Description (Pic. 1-2)
1a. Throttle handle
1b. Handle
2. Power cord
3. Plastic cross-plate
4. 2x central tubes
5. Frame tubing
6. Machine frame
7. Blade roller
8. Carriage bolt
9. Wing nut
10. Tapping screw
11. Cable clip
12. Safety release catch
13. On/Off switch
14. Belt clip
15. Cable suspension
16. Nut M8
17. Screw M8
18. Drive shaft
3. Scope of delivery (Pic. 2)
Electric Tiller
1x Plastic cross-plate (3)
2x Central tubes (4)
4x Carriage bolt (8)
4x Wing nut (9)
2x Tapping screw (10)
1x Cable clip (11)
1x Belt clip (12)
Manual
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage. When complaints the dealer must
be informed immediately. Subsequent complaints
will not be accepted.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION!
m
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!

4. Intended use

The machine is designed for digging over beds and
fields. Be sure to observe the restrictions in the ad-
ditional safety instructions.
The instructions for use contain valuable information
on operating, maintenance and servicing conditions.
For safety reasons, the device must not be used as a
drive unit for other work tools or toolkits of any kind.
GB 21 21