Seite 1
SI 6TU SI 8TU SI 11TU Montage- und SI 14TU Gebrauchsanweisung SI 18 TU Installation and Operating Instructions Instructions d’installation et d’utilisation Sole/Wasser- Brine-to-Water Pompe à chaleur Wärmepumpe für Heat Pump for eau glycolée-eau Innenaufstellung Indoor Installation pour installation intérieure Bestell-Nr.
SI 6TU - SI 18TU Bitte sofort lesen 1.2 Bestimmungsgemäßer Gebrauch 1.1 Wichtige Hinweise Dieses Gerät ist nur für den vom Hersteller vorgesehenen Ver- wendungszweck freigegeben. Ein anderer oder darüber hinaus ACHTUNG! gehender Gebrauch gilt als nicht bestimmungsgemäß. Dazu Für den Betrieb und die Wartung einer Wärmepumpe sind die rechtlichen zählt auch die Beachtung der zugehörigen Projektierungsunter-...
SI 6TU - SI 18TU Verwendungszweck der Grundgerät Wärmepumpe Das Grundgerät besteht aus einer anschlussfertigen Wärme- pumpe für Innenaufstellung mit Blechgehäuse, Schaltkasten und integriertem Wärmepumpenmanager. Der Kältekreis ist „herme- 2.1 Anwendungsbereich tisch geschlossen“ und enthält das vom Kyoto-Protokoll erfasste fluorierte Kältemittel R410A mit einem GWP-Wert von 1975. Es Die Sole/Wasser-Wärmepumpe ist ausschließlich für die Erwär-...
SI 6TU - SI 18TU Zubehör Transport Zum Transport auf ebenem Untergrund eignet sich ein Hubwa- 4.1 Soleverteiler gen. Muss die Wärmepumpe auf unebenem Untergrund oder über Treppen befördert werden, kann dies mit Tragriemen ge- Der Soleverteiler vereinigt die Kollektorschleifen der Wärmequel- schehen.
SI 6TU - SI 18TU Aufstellung Montage 6.1 Allgemeine Hinweise 7.1 Allgemein Die Sole/Wasser-Wärmepumpe muss in einem frostfreien und An der Wärmepumpe sind folgende Anschlüsse herzustellen: trockenen Raum auf einer ebenen, glatten und waagerechte Flä- Vor-/Rücklauf Sole (Wärmequellenanlage) che aufgestellt werden. Dabei sollte der Rahmen rundum dicht ...
SI 6TU - SI 18TU 7.4 Temperaturfühler Mindestheizwasserdurchsatz Der Mindestheizwasserdurchsatz der Wärmepumpe ist in jedem Folgende Temperaturfühler sind bereits eingebaut bzw. müssen Betriebszustand der Heizungsanlage sicherzustellen. Dieses zusätzlich montiert werden: kann z.B. durch Installation eines doppelt differenzdrucklosen Außentemperatur (R1) beigelegt (NTC-2) Verteilers oder eines Überströmventiles erreicht werden.
SI 6TU - SI 18TU 7.4.2 Montage des 7.4.4 Verteilsystem Hydraulik Außentemperaturfühlers Kompaktverteiler und Doppelt differenzdruckloser Verteiler fun- gieren als Schnittstelle zwischen der Wärmepumpe, dem Hei- Der Temperaturfühler muss so angebracht werden, dass sämtli- zungsverteilsystem, dem Pufferspeicher und evtl. auch dem che Witterungseinflüsse erfasst werden und der Messwert nicht...
SI 6TU - SI 18TU 7.5.2 Elektrische Anschlussarbeiten 11) Bei der Wärmepumpen ist der Rücklauffühler integriert und wird über die Steuerleitung zum Wärmepumpenmanager Die 4-adrige elektrische Versorgungsleitung für den Leis- geführt. Nur beim Einsatz eines Doppelt-Differenzdruck- tungsteil der Wärmepumpe wird vom Stromzähler der Wär- losen-Verteilers muss der Rücklauffühler in der Tauch-...
SI 6TU - SI 18TU Pflege / Reinigung 8.3 Vorgehensweise bei Inbetriebnahme 9.1 Pflege Die Inbetriebnahme der Wärmepumpe erfolgt über den Wärme- pumpenmanager. Um Betriebsstörungen durch Schmutzablagerungen in den Wär- metauschern zu vermeiden, ist dafür Sorge zu tragen, dass kei- ACHTUNG! nerlei Verschmutzungen in die Wärmequellen- und Heizungsan-...
SI 6TU - SI 18TU 10 Störungen / Fehlersuche Diese Wärmepumpe ist ein Qualitätsprodukt und sollte störungs- frei arbeiten. Tritt dennoch eine Störung auf, wird diese im Dis- play des Wärmepumpenamanagers angezeigt. Schlagen Sie dazu auf der Seite Störungen und Fehlersuche in der Ge- brauchsanweisung des Wärmepumpenmanagers nach.
SI 6TU - SI 18TU 12 Geräteinformation Typ- und Verkaufsbezeichnung SI 6TU SI 8TU SI 11TU Bauform Ausführung Universal Universal Universal Regler Intern Intern Intern Wärmemengenzählung integriert integriert integriert Aufstellungsort / Schutzart nach EN 60 529 Innen / IP 21...
Seite 14
SI 6TU - SI 18TU Typ- und Verkaufsbezeichnung SI 14TU SI 18TU Bauform Ausführung Universal Universal Regler Intern Intern Wärmemengenzählung integriert integriert Aufstellungsort / Schutzart nach EN 60 529 Innen / IP 21 Innen / IP 21 Leistungsstufen Einsatzgrenzen 20 bis 62 ±2 20 bis 62 ±2...
SI 6TU - SI 18TU 13 Garantieurkunde Eine Verlängerung der Garantie auf 60 Monate für Heizungs- Wärmepumpe und zentrale Wohnungslüftungsgeräte ab Inbe- triebnahmedatum, jedoch maximal 72 Monate ab Auslieferung Glen Dimplex Deutschland GmbH Werk bzw. 78 Monate ab Fertigungsdatum, wird gemäß den Garantieurkunde Systemtechnik nachfolgenden Bedingungen gewährt: Voraussetzung für die...
Seite 16
SI 6TU - SI 18TU DE-14 452235.66.05 · FD 9304 www.dimplex.de...
Seite 17
SI 6TU - SI 18TU Table of contents Please Read Immediately ......................EN-2 1.1 Important Information........................... EN-2 1.2 Intended Use ............................EN-2 1.3 Legal Regulations and Directives ......................EN-2 1.4 Energy-Efficient Use of the Heat Pump ....................EN-2 Purpose of the Heat Pump ......................EN-3 2.1 Application ............................
SI 6TU - SI 18TU Please Read 1.2 Intended Use Immediately This device is only intended for use as specified by the manufac- turer. Any other use beyond that intended by the manufacturer is prohibited. This requires the user to abide by the relevant project 1.1 Important Information...
SI 6TU - SI 18TU Purpose of the Heat Basic Device Pump The basic device consists of a ready-to-use heat pump for indoor installation, complete with sheet metal casing, control panel and integrated manager. The refrigerant circuit is hermetically 2.1 Application sealed.
SI 6TU - SI 18TU Accessories Transport A lift truck is suited for transporting the unit on a level surface. 4.1 Brine Circuit Manifold Carrying straps may be used if the heat pump needs to be trans- ported on an uneven surface or carried up or down stairs. These The brine circuit manifold merges the individual collector loops of straps can be passed directly underneath the wooden pallet.
SI 6TU - SI 18TU 6.2 Acoustic Emissions Minimum heating water flow rate The minimum heating water flow rate through the heat pump The heat pump operates silently due to efficient sound insulation. must be assured in all operating states of the heating sys- Internal insulation measures should be carried out to prevent vi- tem.
SI 6TU - SI 18TU 7.4 Temperature sensor 7.4.2 Mounting the external temperature sensor The following temperature sensors are already installed or must be installed additionally: The temperature sensor must be mounted in such a way that all External temperature sensor (R1) supplied (NTC-2) weather conditions are taken into consideration and the meas- ...
SI 6TU - SI 18TU 7.5 Electrical connection The utility blocking contactor (K22) with 3 main contacts (1/ 3/5 // 2/4/6) and an auxiliary contact (NO contact 13/14) should be dimensioned according to the heat pump output 7.5.1 General and must be supplied by the customer.
SI 6TU - SI 18TU Commissioning Maintenance and Cleaning 8.1 General Information 9.1 Maintenance To ensure that start-up is performed correctly, it should only be carried out by an after-sales service technician authorised by the To prevent faults due to sediment in the heat exchangers, care manufacturer.
SI 6TU - SI 18TU 10 Faults / Trouble- 11 Decommissioning / Shooting Disposal This heat pump is a quality product and is designed for trouble- Before removing the heat pump, disconnect it from the power free operation. In the event that a fault should occur, it will be in- source and close all valves.
SI 6TU - SI 18TU 12 Device Information Type and order code SI 6TU SI 8TU SI 11TU Design Model Universal Universal Universal controller Intern Intern Intern Thermal energy metering Integreated Integreated Integreated Installation location / degree of protection according to EN 60 529...
Seite 27
SI 6TU - SI 18TU Type and order code SI 14TU SI 18TU Design Model Universal Universal controller Intern Intern Thermal energy metering Integreated Integreated Installation location / degree of protection according to EN 60 529 Indoors / IP 21...
Seite 28
SI 6TU - SI 18TU EN-12 452235.66.05 · FD 9304 www.dimplex.de...
Seite 29
SI 6TU - SI 18TU Table des matières A lire immédiatement !....................... FR-2 1.1 Remarques importantes ........................FR-2 1.2 Utilisation conforme ..........................FR-2 1.3 Dispositions légales et directives......................FR-2 1.4 Utilisation de la pompe à chaleur pour économiser de l'énergie ............FR-2 Utilisation de la pompe à chaleur ..................... FR-3 2.1 Domaine d’utilisation..........................FR-3...
SI 6TU - SI 18TU A lire immédiatement ! 1.2 Utilisation conforme Cet appareil ne doit être employé que selon les conditions d'utili- 1.1 Remarques importantes sation prévues par le fabricant. Toute autre utilisation est consi- dérée comme non conforme. La documentation accompagnant les projets doit également être prise en compte.
SI 6TU - SI 18TU Utilisation de la pompe Appareil de base à chaleur Il s'agit d'une pompe à chaleur pour installation intérieure, prête à brancher, avec boîtier, compartiment électrique et gestionnaire de pompe à chaleur intégré. Le circuit réfrigérant est "herméti- 2.1 Domaine d’utilisation...
SI 6TU - SI 18TU Accessoires Transport Le transport par chariot élévateur convient bien à un déplace- 4.1 Distributeur d'eau glycolée ment sur surface plane. Si la pompe à chaleur doit être convoyée sur une surface non plane ou dans des escaliers, il est possible Le distributeur d’eau glycolée réunit les boucles du collecteur de...
SI 6TU - SI 18TU Installation Montage 6.1 Généralités 7.1 Remarques d’ordre général La pompe à chaleur eau glycolée/eau doit être installée dans un Les raccordements suivants doivent être réalisés sur la pompe à local sec à l'abri du gel, sur une surface plane, lisse et horizon- chaleur : tale.
SI 6TU - SI 18TU 7.4 Sonde de température Débit d'eau de chauffage minimum Quel que soit l'état de fonctionnement de l'installation de chauf- Les sondes de températures suivantes sont déjà montées ou fage, un débit d'eau de chauffage minimum doit être garanti dans doivent être installées en plus :...
SI 6TU - SI 18TU 7.4.2 Montage de la sonde de température 7.4.4 Système de distribution hydraulique extérieure Le distributeur compact et le distributeur double sans pression différentielle servent d'interface entre la pompe à chaleur, le sys- La sonde de température doit être placée de telle sorte qu’elle tème de distribution de chauffage, le ballon tampon et éventuel-...
SI 6TU - SI 18TU 7.5.2 Branchements électriques 10) La pompe de puits ou d’eau glycolée (M11) est branchée aux bornes X2/N et X2/M11 et PE. La ligne d’alimentation à 4 fils électriques de la partie puis- 11) Pour les pompes à chaleur, la sonde sur circuit de retour sance de la pompe à...
SI 6TU - SI 18TU Entretien / nettoyage 8.3 Procédures à suivre lors de la mise en service 9.1 Entretien La mise en service de la pompe à chaleur s’effectue via le ges- tionnaire de pompe à chaleur. Pour éviter des dysfonctionnements dus à des dépôts dans les échangeurs thermiques de la pompe à...
SI 6TU - SI 18TU 9.3 Nettoyage côté source de chaleur ATTENTION ! Monter, sur la pompe à chaleur, le filtre qui vous est livré dans l’ouverture d’admission de la source de chaleur, afin de protéger l’évaporateur des salissures. Il est recommandé de nettoyer le filtre du filtre un jour après la mise en service.
SI 6TU - SI 18TU 12 Informations sur les appareils Désignation technique et commerciale SI 6TU SI 8TU SI 11TU Forme Version Universelle Universelle Universelle Régulateur interne interne interne Calorimètre intégré intégré intégré Emplacement / degré de protection selon EN 60 529 en intérieur/ IP 21...
Seite 40
SI 6TU - SI 18TU Désignation technique et commerciale SI 14TU SI 18TU Forme Version Universelle Universelle Régulateur interne interne Calorimètre intégré intégré Emplacement / degré de protection selon EN 60 529 en intérieur / IP 21 en intérieur / IP 21...
SI 6TU - SI 18TU 2 Diagramme / Diagrams / Diagrammes 2.1 Kennlinien / Characteristic Curves / Courbes caractéristiques SI 6TU A-IV 452235.66.05 · FD 9304...
Seite 45
SI 6TU - SI 18TU 2.2 Kennlinien / Characteristic Curves / Courbes caractéristiques SI 8TU www.dimplex.de 452235.66.05 · FD 9304...
Seite 46
SI 6TU - SI 18TU 2.3 Kennlinien / Characteristic Curves / Courbes caractéristiques SI 11TU A-VI 452235.66.05 · FD 9304...
Seite 47
SI 6TU - SI 18TU 2.4 Kennlinien / Characteristic Curves / Courbes caractéristiques SI 14TU www.dimplex.de 452235.66.05 · FD 9304 A-VII...
Seite 48
SI 6TU - SI 18TU 2.5 Kennlinien / Characteristic Curves / Courbes caractéristiques SI 18TU A-VIII 452235.66.05 · FD 9304...
Seite 49
SI 6TU - SI 18TU 2.6 Einsatzgrenzendiagramm / Operating limits diagram / Diagramme des seuils d'utilisation SI 6TU - SI 18TU Wasseraustritt (+/- 2 K) Water outlet (+/- 2 K) Sortie d'eau (+/- 2 K) Wärmequelleneintrittstemperatur [°C] Heat source inlet temperature [°C] Température d'entrée de la source de chaleur [°C]...
SI 6TU - SI 18TU 3 Stromlaufpläne / Circuit Diagrams / Schémas électriques 3.1 Steuerung / Control / Commande 452235.66.05 · FD 9304...
Seite 51
SI 6TU - SI 18TU 3.2 Steuerung / Control / Commande www.dimplex.de 452235.66.05 · FD 9304 A-XI...
Seite 52
SI 6TU - SI 18TU 3.3 Last / Load / Charge A-XII 452235.66.05 · FD 9304...
Seite 53
SI 6TU - SI 18TU 3.4 Anschlussplan / Connection Plan /Schéma de connexion www.dimplex.de 452235.66.05 · FD 9304 A-XIII...
Seite 54
SI 6TU - SI 18TU 3.5 Anschlussplan / Connection Plan /Schéma de connexion A-XIV 452235.66.05 · FD 9304...
Seite 55
SI 6TU - SI 18TU 3.6 Legende / Legend / Légende Brücke EVU-Sperre, muss eingelegt werden, wenn Utility block (EVU) bridge must be inserted if no Pont de blocage de la société d'électricité, à insérer kein EVU-Sperrschütz vorhanden ist utility blocking contactor is present en absence de contacteur de blocage de la société...
Seite 56
SI 6TU - SI 18TU R13* Fühler regenerativ, Raumfühler, Fühler 3. Heizkreis Renewable sensor, room sensor, sensor for Sonde mode régénératif, sonde d'ambiance, sonde heating circuit 3 3ème circuit de chauffage Rücklauffühler Primärkreis Return sensor, primary circuit Sonde retour circuit primaire Drucksensor Kältekreis - Niederdruck pO...
SI 6TU - SI 18TU 4 Hydraulisches Einbindungsschema / Hydraulic integration diagram / Schéma d'intégration hydraulique 4.1 Monovalente Wärmepumpenanlage mit einem Heizkreis und Warmwasserbereitung / Monovalent heat pump system with one heating circuits and domestic hot water preparation / Installation monovalente de pompe à...
SI 6TU - SI 18TU 5 Konformitätserklärung / Declaration of Conformity / Déclaration de conformité EG - Konformitätserklärung EC Declaration of Conformity Déclaration de conformité CE Der Unterzeichnete Glen Dimplex Deutschland GmbH The undersigned Geschäftsbereich Dimplex L’entreprise soussignée, Am Goldenen Feld 18 D - 95326 Kulmbach bestätigt hiermit, dass das (die)
Seite 60
Glen Dimplex Deutschland GmbH Irrtümer und Änderungen vorbehalten. Geschäftsbereich Dimplex Subject to alterations and errors. Am Goldenen Feld 18 Sous réserve d’erreurs et modifications. D-95326 Kulmbach +49 (0) 9221 709 565 www.dimplex.de...