Technical Data; Before Putting The Machine Into Operation - EINHELL RT-TS 1825 U Originalbetriebsanleitung

Anleitung_RT_TS_1825_U_SPK1_- 26.09.13 15:40 Seite 16
GB
connection with the machineʼs construction and
design:
Contact with the saw blade in the uncovered
n
saw zone.
Reaching into the running saw blade (cut
n
injuries).
Kick-back of workpieces and parts of work-
n
pieces.
Saw blade fracturing.
n
Catapulting of faulty carbide tips from the saw
n
blade.
Damage to hearing if ear-muffs are not used as
n
necessary.
Harmful emissions of wood dust when used in
n
closed rooms.

5. Technical data

AC motor
Power P S1 1500 W S6 40% 1800 W
Idle speed n
0
Cutting-off wheel
Number of teeth
Table size
Table width extension, left/right
Table length extension, rear
Cutting height max.
Height adjustment
Tilting saw blade
Extractor socket
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
Sound pressure level LPA 104,5 dB(A)
K uncertainty
pA
Sound power level LWA
K uncertainty
WA
The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
16
230V - 240V 50Hz
5700 min -1
Ø 250 x Ø 30 x 2.4 mm
24
625 x 440 mm
625 x 250 mm
400 x 440 mm
73 mm/90°
53 mm / 45°
infinite 0 -73 mm
infinite 0° - 45°
Ø 36 mm
Idle mode
95,5 dB(A)
3 dB
114,1 dB(A) 105,2 dB(A)
3 dB
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved.
Wear ear-muffs.
The impact of noise can cause damage to hearing.
„Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
n
order.
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
n
necessary.
Switch the appliance off when it is not in use.
n
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
1. Lung damage if no suitable protective dust mask
is used.
2. Damage to hearing if no suitable ear protection is
used.
6. Before putting the machine into
operation
Unpack the bench-type circular saw and check it
n
for damage which may have occurred in transit.
The machine has to be set up where it can stand
n
firmly, e.g. on a work bench, or it must be bolted
to a strong base.
All covers and safety devices have to be
n
properly fitted before the machine is switched
on.
It must be possible for the saw blade to run
n
freely.
When working with wood that has been
n
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
n
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
n
supply, make sure the data on the rating plate is
the same as that for your mains.