Safety Warnings; General Power Tool Safety Warnings; Intended Use; Misuse - HellermannTyton Autotool 2000 CPK Montageanleitung

Texts accompanied by this symbol contain useful additional
information.
2

Safety warnings

The safety warnings in the Operating instructions for the
AT2000 CPK also apply to operation of the AT2000 CPK after
installation in the force measurement device CPK.
2 1

General power tool safety warnings

WARNING
Non-compliance with the safety warnings below can
lead to severe injuries, fire and electric shock
f Comply with the instructions and warnings below.
f Keep the Operating instructions for the AT2000 CPK
ready to hand.
2 2

Intended use

Use the Force Measurement Device CPK when it is in full
working order and safe, always be safety-conscious and
aware of the hazards.
The Force Measurement Device CPK with integrated
AT2000 CPK is suitable for and intended for the following
uses:
• Measuring the linear tensile force on cable tie
• For indoor use only
• Industrial use
2 3

Misuse

Use other than that stated in the section entitled "Intended
use" is misuse. The operating company responsible for use of
the apparatus bears sole responsibility for injury and damage
resulting from misuse.
The safety regulations for the AT2000 CPK (see the
Operating Instructions for the AT2000 CPK) apply in
addition.
The following are specifically prohibited:
• Use with faulty parts
• Use in explosive environments or in the presence of a fire
hazard
• Use outdoors
• Use in high humidity and/or direct sunlight
• Manipulation while processes are in progress
• Unauthorised alterations and modifications to the
apparatus and its component parts without the prior
consent of HellermannTyton
• Use of spare parts and accessories not tested and
approved beforehand by HellermannTyton
2 4

Personnel qualification

Underage persons and trainees are permitted to use the
device only under the supervision of an experienced
specialist and only with the express permission of the
operating company.
Assembly Instructions • Force Measurement Device CPK • 04/2018 • v03 • 102-01002

2 4 1 Specialist personnel for operation

The tasks and authorisations assigned to specialist personnel
for extended operation are as follows:
• Operation of the products
• Rectification of faults or, as applicable, initiation of
measures for the rectification of faults
• Cleaning of the products
These individuals have the specialist training or practical
experience that will ensure correct handling.
2 4 2 Specialist personnel for maintenance and repair
Always have maintenance and repair work carried out by
duly qualified specialist personnel. These individuals have
received training that affords sufficient knowledge of the
AT2000 CPK or the Force Measurement Device CPK for them
to judge when it is in safe working order.
These individuals are also familiar with the following rules
and regulations:
• Applicable national health and safety regulations
• Accident prevention regulations
• Generally accepted codes of practice, regulations and
standards
2 4 3 Authorised person for low-voltage electrical
equipment
Work on the electrical supply and on parts that are live when
the device is in operation should always be carried out by a
person duly authorised to work on low-voltage electrical
equipment.
2 4 4 Authorised specialist for repair and testing
Only service technicians from HellermannTyton or service
technicians authorised by HellermannTyton are permitted to
carry out repairs and safety checks.
2 5 Underlying hazards associated with use of the
AT2000 CPK or the
Force Measurement Device CPK

2 5 1 Electricity

f Always wear safety glasses and suitable safety
equipment whilst working.
f Before installation, cleaning and maintenance,
disconnect the AT2000 CPK and the power pack CPK
from the power supply.

2 5 2 Cleanliness at the workplace

Orderliness, good lighting and cleanliness at the workplace
all help to make work easier and to minimise hazards and
the risk of injury.
Always comply with the following principles of orderliness
and cleanliness at the workplace:
f Put tools away as soon as they are no longer needed.
f Avoid trips (e.g. immediately dispose of waste by placing
it in the containers provided for the purpose).
Safety warnings
5