Working Instructions - Scheppach 5904802903 Anleitung

4. Pull the recoil starter handle (9) 3-5 times to start the
engine. Fig. 21
Never place feet on the shaft or kneel on it.
5. Wait a while adjust the choke lever to
Fig. 22
6. When the engine is running and idling. First press
the lock off lever (8) and then switch the throttle lever
(11) on, the machine will be working. Fig. 23
7. If meet any problems, press the engine switch to off
position, the machine will stop running. If need stop
cutting head working, release the throttle lever (11).
Fig. 23
8. If any problem occurs, pull the pin of safety belt, then
release the brush cutter immediately. Fig. 17
9. If the machine is hot, the throttle level can be
adjusted to ON position directly when re start the
machine.
Note: If the engine does not start up even after several
attempts, read the section „Engine troubleshooting".
Note: Always pull the starter cord out in a straight line. If
it is pulled out at an angle, then friction will occur on the
eyelet. As a result of this friction, the cable will become
frayed and will wear away faster. Always hold the starter
handle when the cable retracts.
Never allow the cable to snap back when it has been
pulled out.
Note: Do not start the motor in tall grass.
m Attention: When the engine has been switched off,
the cutting unit continues running for several seconds
therefore do not touch the cutting unit until it has come
to a standstill!

9. Working instructions

Working with brush cutter / grass trimmer
•
time, familiarize yourself with the operation and control
of the petrol cutting blade without running engine.
• The design of the petrol brush cutter allows for
operation only at the right side of the user's body.
•
the handles.
• Always make sure that the cutting tool continues to
• Always so that the cutting tool no longer turns in a
proper engine idle not press down the throttle.
• Always work with high speed so you have the best
cutting results.
• Poke when working on a stone or a tree, turn off the
engine and remove the spark plug then examine the
petrol brush cutter for damage.
• Caution: Always be extra careful when working in
as not to overload the unit.
• Always wear safety glasses and hearing protection
and a safety helmet.
Mowing with grass trimmer
• Use the plastic line cassette for a clean cut also at
uneven edges, fencing posts, and trees.
position. • Carefully advance the trimming line to an obstacle,
and use the tip of the line to cut around the obstacle.
When the trimming line comes into contact with
stones, trees, and walls, the line wears out or breaks
off ahead of time.
• Swing the petrol cutting blade like a normal scythe
horizontally from right to left and back again. You
are holding the tool.
• Never replace the nylon line with a metal wire.
RISK OF INJURIES
Mowing with brush cutter and hedge trimmer
Use the cutting blade to comb through brushwood,
rank growth, young tree populations (trunk diameter of
maximum 2 cm), and high grass.
• While using metal cutting tools, there is generally
a risk of recoil, when the tool hits a solid obstacle
(stones, trees, branches, etc.). Thereby, the tool is
hurled backwards against the rotating direction.
• To cut rank growth and brushwood, you "immerse" the
cutting blade from the top.
CAUTION: Be especially careful, when using this
working technique, because the further away the cutting
tool is from the ground, the higher is the risk that objects
to be cut and particles will be hurled sideways.
CAUTION: Incorrect use and misuse can damage the
bush cutter and cause severe injuries because of pieces
hurled away.
To minimize the risk of accidents by use of the cutting
blade, take note of following points:
• Never cut shrubbery or wood whose diameter is larger
than 2 cm.
• Avoid contact with metal bodies, stones, etc.
• Periodically check the cutting blade for damages.
Never continue to use a damaged cutting blade.
• When the cutting blade becomes apparently blunt, it
must be sharpened according to instructions. When
the cutting blade is apparently out of balance, it must
be replaced.
Automatic thread trimming (Fig. 36)
cassette.
This line will wear out during work. To feed new line,
forcefully press the head of the line cassette onto the
ground while the engine is running at working speed.
The line is automatically fed due to centrifugal force.
The knife at the line guard will shorten the trimming line
to the correct length.
Run the trim line approach cautiously to an obstacle and
cut with the tip of the line around the obstacle.
GB 31