Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Whip aerials, flagstocks, compass, searchlights, telephone aerial, towing cable, self-adhesive decals, spare anchor,
lighting, Figs. 201 - 207, Plan II
Part
Description
No.
447
Plinth
448
Whip aerial
449
Whip aerial cap
450
Flagstock brace
451
Flagstock
452
Dutch national flag
453
Flagstock cap
454
Compass cowl
455
Compass housing
456
Searchlight
457
Searchlight plinth
458
Signal halyard
459
Dockyard flag
460
Telephone aerial
461
Towing cable
462 a - x
Self-adhesive decals
463
Anchor
464
Anchor bracket
465
Lamp
466
Steamer lamp
467
Clear bulb
468
Red bulb
469
Green bulb
470
Flexible cable
471
Heat-shrink sleeve
472
10-pin connector
- Assemble the two whip aerials for the top deck from parts
447 - 449. Note that the wires 448 are of different length,
as shown on the plan.
- Make up the flagstock from the brass wire parts 450 and
451, and attach it to the top deck as shown in the plan
view. Fit the Dutch national flag 452 and the cap 453 on
the flagstock.
- Assemble the compass (parts 454, 455) and the search-
lights (parts 456, 457) and glue them in place as shown.
- Tie the signal halyards 458 to the yard blocks, and the
signal yards on the foremast and mainmast, attaching the
dockyard flag 459 at the same time.
- Run the telephone aerial 460 on the port side from the
mainmast block to the foremast block. Extend part of the
aerial to the aerial holder 316 on the funnel.
- The towing cable 461 is supplied as a length of thread
about 2500 mm long; tie a loop in each end, wrap the
ends with thread and secure the loop ends with a drop of
cyano.
- Run one end of the towing cable through the opening in
the aft bulkhead and into the hull, where it should be
connected to the towing mechanism. Coil up the other
end and position it on the after deck behind the hawser
bars.
- Bend the anchor brackets 464 to the shape shown, and
use them to attach the spare anchor 463 to the aft super-
structure wall.
Assembly instructions
Happy Hunter
Material
Plastic
Brass
Glass
Brass
Brass
Fabric
Glass
Plastic
Beech
Metal
Spruce
Thread
Fabric
Thread
Thread
---
Metal
Brass
Plastic
Plastic
---
---
---
---
---
---
The lighting system
- Install the bulbs 467 - 469 as shown in the "Lamp assem-
bly" diagram on Plan II. Note the correct location of the
coloured bulbs. Extend the connecting wires 470 to suit,
and run them downward. The bulbs should be wired up in
parallel. We recommend that you install a 10-pin connec-
tor 472 in the wiring harness to enable you to remove the
superstructure at any time. The stern lamp should also be
connected using a plug and socket.
- Position the lamps 456 and 466. Glue the navigation
lamps in place after fitting the bulbs from the underside.
Note on lighting system
The wiring diagram shows the method of connecting the
bulbs to the three unused Multi-Switch channels.
If you wish to install a scale lighting system, at least one
additional electronic switching facility is required.
The separate sheet entitled "Lighting system" shows how
the individual groups of lamps are wired together and
connected to the individual channels.
Your model is now complete.
47
Size in mm
No.
off
Inj. moulded
3
1 Ø
3
3.5 O.D.
3
0.8 Ø
1
1 Ø
1
Ready made
1
3.5 O.D.
1
Inj. moulded
1
8 Ø x 21
1
Ready made
2
8 x 8 x 12
2
0.2 Ø
10
Ready made
1
0.2 Ø, 2-part
1
1 Ø x 2500
1
---
1
Ready made
1
1 Ø
1
5.4 Ø x 12, inj.
5
5.4 Ø x 12, inj.
8
3 Ø, 6 Volt
10
3 Ø, 6 Volt
4
3 Ø, 6 Volt
1
0.07 mmÇ
1
2.4 Ø
1
---
1
Order No.
1106
Notes
As plan
FS, bead
As plan
FS
FS, bead
FS
FS
FS, as plan
FS
FS, as plan
FS
Set
FS
As plan
FS
FS
FS
FS
FS
Not included
Not included
Not included
Werbung
