Werbung
Verfügbare Sprachen
Verfügbare Sprachen
- Make one ladder for the main mast and one for the fore-
mast. Solder overlength pieces of brass wire to them to
form the spacer pins 393, then shorten them to 4 mm.
The ladders are not required until the masts have been
assembled.
- Drill holes in the deck lamps 394, bend the deck lamp
stands 395 to shape and glue them in the holes. Drill 1
mm Ø holes in the deck and glue the deck lamps in the
holes and to the handrail.
Light shaft, return pulleys, stern lamp console, lifebelts,
gangway, liferaft support
- Attach the brass wire latches 397 to the light shaft 396,
and glue the glazed porthole 398 in place. Glue the com-
pleted light shaft to the boat deck.
- Fit the pulleys 400 and washers 401 on the pulley conso-
les 399, but glue the washers in place only - not the pul-
leys.
The foremast, Figs. 182 - 185, Plan II
Part
Description
No.
409
Foremast
410
Cradle
411
Foremast strut
412
Yard block
413
Angled yard block
414
Ship's bell bracket
415
Ship's bell
- Glue together the injection-moulded parts 409 - 413 to
form the foremast, following the sequence of the part
numbers.
- Hold the prepared ladder against the foremast, mark the
position of the pins 393, and drill 1 mm Ø holes at the
marked points. Glue the ladder in the holes.
The mainmast, Figs. 186 - 191, Plan II
Part
Description
No.
416
Platform
417
Railing stanchion
418
Rail
419
Rail
420
Lower mast section
421
Radar plinth
422
L.H. mast strut
423
R.H. mast strut
424
Radar platform
425
Mast
426
Navigation frame stand
427
Navigation frame
428
Lower signal yard
429
Yard block
430
Upper signal yard
431
Aerial rod
432
Aerial base
433
Aerial cap
434
Foghorn
435
Signal yard strut
436
Radar arm
437
Radar housing
438
Drive shaft
439
Spacer sleeve
440
Coupling sleeve
Assembly instructions
Happy Hunter
- Glue the pulley consoles and the lamp console 402 in
place as shown on the plan. The method of fitting the
stern lamp is described in the "Lighting" section.
- Glue the two-part liferafts 403 together.
- Bend the four catapult arms 404 to shape. We recom-
mend that you make a simple jig for bending these parts.
- Solder the catapult feet 405 to the catapult arms, and sol-
der the catapult struts 406 in place.
- Glue the catapults and the liferafts to the superstructure.
- Attach the lifebelts 407 to the superstructure.
- Make up the gangway from the braces 408 and the lengt-
hs of brass wire 408a, and glue it to the rear of the super-
structure.
Material
ABS
ABS
ABS
ABS
ABS
Brass
Brass
- Bend to shape the bracket 414 for the ship's bell 415. Drill
a 0.8 mm Ø hole, glue the bracket in it, and attach the
ship's bell.
- Drill a 2 mm Ø hole in the superstructure and glue the
foremast in it.
Material
ABS
Brass
Brass
Brass
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
Brass
ABS
Glass
Plastic
Brass
ABS
ABS
Brass
Brass
Plastic
45
Size in mm
No.
off
Inj. moulded
1
Inj. moulded
5
Inj. moulded
1
Inj. moulded
2
Inj. moulded
2
0.8 Ø
1
Ready made
1
Size in mm
No.
off
Inj. moulded
1
25 high, 3 holes
9
1 Ø
1
0.8 Ø
2
Inj. moulded
1
Inj. moulded
1
Inj. moulded
1
Inj. moulded
1
Inj. moulded
1
Inj. moulded
1
Inj. moulded
1
Inj. moulded
1
Inj. moulded
1
Inj. moulded
9
Inj. moulded
1
1 Ø x 140
1
Inj. moulded
1
3.5 O.D.
1
Inj. moulded
2
0.8 Ø x 20
2
Inj. moulded
2
Inj. moulded
2
1 Ø x 140
1
1 Ø x 1.5 Ø x 8
1
1 I.D. x 18
1
Order No.
1106
Notes
As plan
FS
Notes
FS
As plan
As plan
FS, bead
FS
FS
FS
Werbung
