Werbung
Verfügbare Sprachen
Verfügbare Sprachen
The wheelhouse, Figs. 167 - 172, Plan II
Part
Description
No.
345
Wheelhouse floor
346
Fore-and-aft wall, aft
347
Aft wall
348 - 349
Aft transverse wall
350
Fore-and-aft wall, front bottom
351
Transverse wall, bottom
352
Fore-and-aft wall, front top
353
Transverse wall, top
354
Door frame
355
Wheelhouse door
356
Top deck bulwark
357
Top deck
- If you intend to install auxiliary working systems, cut the
oval opening in part 345.
- Assemble the wheelhouse on the wheelhouse floor 345
using the walls 346 - 351. Trim the upper fore-and-aft
walls 352 and the transverse wall 353 to fit, and glue them
in place. Repeat the procedure with the doors 354, 355.
The air shafts, detail drawing entitled "Air shafts", Plan I, Fig. 201
Part
Description
No.
358
Air duct
359
Air duct
360
Side panel
361
Side panel
362
End panel
363
Small end panel
364
Air flap
365
Small air flap
- Assemble the air shafts from parts 358 - 365.
- Cut the air ducts 358 and 359 to length and sand them to
shape.
Assembling the superstructure, Plan II
Part
Description
No.
366
Aft wheelhouse wall glazing
367 - 370
Wheelhouse glazing
371
Upper transverse wall glazing
372
Wheelhouse glazing
373 - 375
Superstructure glazing
376
Aft bulkhead door glazing
377
Glazed porthole
- The individual superstructure sub-assemblies should be
painted at this stage.
- Glue the glazing panels 366 - 375 in place, following the
sequential numbers marked on the plan. The glazing
panel 376 should be attached to the inside of the aft
bulkhead door.
Assembly instructions
Happy Hunter
Material
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
- Trim the underside of the top deck bulwark 356, sand it
flat, and glue it to the top deck 357. Cut away the top area
of the bulwark as shown.
- The superstructure components cannot be glued in place
until the wheelhouse has been painted and glazed.
--
Material
Obechi
Obechi
ABS
ABS
ABS
ABS
ABS
ABS
- Drill holes in the side panel 360 and 361 and trim the parts
to fit. Glue the panels 360 - 365 to the air ducts.
- Glue the completed air shafts to the superstructure.
Material
Plastic
Plastic
Plastic
Plastic
Plastic
Plastic
Brass
- Apply Stabilit-Express to the wheelhouse, glue it to the
bridge deck and position it carefully. Glue the top deck on
the wheelhouse. Glue the completed toolboxes 266, 267
to the top deck.
- Fit the glazing panels in the portholes 377 and glue them
in the hull.
43
Size in mm
No.
off
1.5, die-cut
1
1.5, die-cut
2
1.5, die-cut
1
1.5, die-cut
1 each
1.5, die-cut
2
1.5, die-cut
1
1.5, die-cut
2
1.5, die-cut
1
1.5, die-cut
4
1.5, die-cut
2
1.5, die-cut
1
1.5, die-cut
1
Size in mm
No.
off
5 x 15 x 46
2
5 x 8 x 46
1
1, die-cut
5
1, die-cut
1
1, die-cut
2
1, die-cut
1
1, die-cut
2
1, die-cut
1
Size in mm
No.
off
0.5, die-cut
1
0.5, die-cut
2 each Brown tint
0.5, die-cut
1
0.5, die-cut
2
0.5, die-cut
2 each Brown tint
0.5, die-cut
1
6 Ø x 8 Ø
20
Order No.
1106
Notes
Notes
Notes
Brown tint
Brown tint
Brown tint
Brown tint
Werbung
