Installation; Steering Wheel; Towing Hitch - Stiga VILLA Montageanleitung

2.3.2 Charging using battery charger
When charging using a battery charger, a battery
charger with constant voltage must be used.
Contact your dealer to purchase a battery charger
with constant voltage.
The battery can be damaged if a standard type
battery charger is used.

2.3.3 Installation

The battery is placed under the engine casing. See
fig. 4. Use the screws and the nuts (4:C, D).
During installation. First connect the red cable to
the battery's positive terminal (+). Then connect the
black cable to the battery's negative terminal (-).
If the cables are disconnected/
connected in the wrong order, there is a
risk of a short-circuit and damage to the
battery.
If the cables are interchanged, the
generator and the battery will be
damaged.
Tighten the cables securely. Loose
cables can cause a fire.
The engine must never be driven with
the battery disconnected. There is a risk
of serious damage to the generator and
the electrical system.
2.3.4 Cleaning
If the battery terminals are coated with oxide, they
should be cleaned. Clean the battery terminals with
a wire brush and lubricate them with terminal
grease.
2.4 SEAT
NOTE! To facilitate installation of the seat, ap-
ply a drop of oil to the four screws before screw-
ing them into the seat.
Release the catch (2:S) and fold up the seat
bracket.
Install the mounting in the rear (upper) holes as
follows:
1. Install the shoulder washers (2:F) on the screws
(2:G).
2. Insert the screws through the slots in the
bracket. Place a washer (2:I) between the seat
and the bracket.
3. Tighten the screws in the seat. Tightening
torque: 9±1.7 Nm.
If the screws are tightened more than
9±1.7 Nm, the seat will be damaged.
4. Check that the seat moves easily in the slots in
the bracket.
Install the mounting in the front (lower) holes as
follows:
ENGLISH
1. Install the screw knobs (2:H) on the screws
(2:G).
2. Install a washer (2:I) on each screw.
3. Insert the screws through the slots in the bracket
and tighten by hand in the seat.
4. Fold the seat down and place it in the desired
position.
5. Tighten the screw knobs (2:H) by hand.
The screw knobs (2:H) and the seat will
be damaged if tools are used.
The seat can be folded. If the machine is parked
outside when it is raining, fold the seat forward to
protect the seat cushion from getting wet.
The seat is locked. To fold the seat up or down,
release the catch (2:S).

2.5 STEERING WHEEL

In order to minimise the axial play in the steering
column, the shim washers (5:K) and/or (5:L) must
be installed on the steering column between the
steering column jacket and the bracket as follows.
1. Install the steering column jacket on the
steering column and secure by knocking in the
tension pin (5:J) approximately 1/3 of its length.
2. Pull the steering column jacket and the steering
column up.
3. From the outside, check whether no washers,
the 0.5 mm washer, the 1.0 mm washer or both
washers can be inserted into the gap. The
washer/washers must not be forced in, as there
must be a little axial play.
4. Pull out the cotter pin and dismantle the steering
wheel jacket.
5. Install the washer/washers in accordance with
point 3 above.
6. Install the steering column jacket on the
steering column and secure by knocking in the
tension pin fully. Use a counterhold.
The steering wheel should be installed so that the
steering wheel boss is in the "10 o'clock position" .

2.6 TOWING HITCH

Screw the towing hitch (6:A) into the two holes on
the underside of the rear axle using screws (6:B).
Tighten the screws properly.
Tightening torque: 22 Nm.
Original instructions for use
EN
17