Operation, Hints And Tips - Ferm FTB-13 Gebrauchsanweisung

Tischbohrmaschine

Vorschau ausblenden Andere Handbücher für FTB-13:

Gebrauchsanweisung (44 Seiten)

Inhalt

Inhaltsverzeichnis

REPLACING CABLES OR PLUGS

Immediately throw away old cables or plugs when they

have been replaced by new ones. It is dangerous to insert

the plug of a loose cable in the wall outlet.

USING EXTENSION CABLES

Only use an approved extension cable suitable for the

power input of the machine. The minimum conductor

size is 1.5 mm

. When using a cable reel always unwind

the reel completely.

ASSEMBLY

Fig.B

•

Place the footplate (13) in the correct position.

•

Fasten the column (11) with the bolts supplied (12)

to the footplate.

•

Now slide the table holder (10) with the table over

the column (11). With the fastening handle (6) the

table is fastened into the desired position.

•

Now you can assemble the machine casing (7) and

lock with the locking pins (8).

•

Since the drill spindle is greased in the factory, it is

advisable to run in the machine for approximately 15

minutes at the lowest speed.

Before you push the chuck with pin (9) into the drill

spindle, the inside of the chuck must be completely

grease-free!

SETTING UP THE BENCH DRILL

Before use the drill must be mounted on a fixed base.

The footplate (13) has therefore been provided with

drilling holes. By means of screws the footplate can be

fixed to the base in this place. If it is mounted on a

wooden board, sufficiently large washers must be used

on the opposite side, so that the bolts are not pushed

into the wood and the machine cannot become loose.

The fastening screws may be fastened so far that

the footplate is not under tension or deformed.

When the tension is too high there is a risk of breakage.

ADJUSTING THE NUMBER OF

REVOLUTIONS OF THE DRILL SPINDLE

Fig.C

The different revolutions of the drill spindle can be

adjusted by shifting the V-belt into the belt drive. The

machine is protected by a safety switch so that the

machine is automaticly switched off when opening the

casing.

The V-belt is shifted as follows:

•

Open the V-belt cover (14) by loosen the screw on

the right side of the cover.

•

Loosen the fastening button (18) and slide the engine

in the direction of the machine head, upon which the

V-belt is released.

•

Shift the V-belt according to the table on the inside of

the V-belt cover.

•

Tension the V-belt again by pushing the engine plate

(17) to the back. Then the tensioning device is

fastened with the fastening button (18).

•

Close the V-belt cover and the machine is ready again

for use.

Keep the V-belt cover closed during use.

Fig.C & D

If you have shifted the V-belt, you must tighten it again by

means of the engine plate (17) with the fastening button

(18). The tension is correct when the V-belt can be

pressed in by approximately 1 cm.

The engine pulley must be aligned horizontally, so that

early wear and loosening of the V-belt can be prevented.

For this purpose the engine pulley (15) on the engine can

be slid along the engine axle, after loosening the socket

head screw.

SPINDLE SPEEDS

Fig.E

Position V-belt

Revolutions/min

2650

1650

1220

850

580

The number of revolutions of the drill spindle of the V-

belt combinations can be read from the illustration and

the table.

DRILL SPINDLE AND DRILL HEAD PIN

All the blank parts of the machine are provided with a

protective lacquer layer, which prevents rust formation.

This protective lacquer layer is easy to remove by means

of environmentally friendly solvents. Test the V-belt

tension before you connect the machine to the

electricity mains.

The inside of the drill spindle must be degreased

completely. For this purpose use environmentally

friendly solvents. Proceed in the same way with the drill

head pin. A correct transmission can only be achieved in

this way.