Scheppach HM100Lxu Originalbetriebsanleitung Seite 26

Attention! The machine executes an upward stroke au-
tomatically due to the return spring, i.e. do not release
the handle (1) after completing the cut; instead allow the
machine head to move upwards slowly whilst applying
light counter pressure.
8.4 Cross cut 90° and turntable 0° - 45° (Fig. 9)
The crosscut saw can be used to make crosscuts of
0° -45° to the left and 0° -45° to the right in relation to
the stop rail.
Important. To make 90° crosscuts, the adjustable stop
rail (16a) must be fixed at the inner position.
• Open the set screw (16b) for the adjustable stop rail
and push the adjustable stop rail inwards.
• The adjustable stop rail (29) must be fixed far enough
in front of the innermost position that the distance
between the stop rail (16a) and the saw blade (6)
amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (16a) and
the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Loosen set screw (26).
• Use the handle (11) to adjust the rotary table (14) to
the desired angle. The pointer (12) on the rotary table
must match the desired angle on the scale (13) on the
fixed saw table (15).
• Re-tighten the set screw (26) in order to secure the
rotary table (14).
• Cut as described under section 8.3.
8.5 Precision adjustment of the stop for mitre cut
45° (Fig. 1/10/11)
• No stop angle included.
• Lower the machine head (4) and secure using the
locking bolt (23).
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22) and use the handle (1) to
angle the machine head (4) 45° to the left.
• 45° - position angle stop (b) between the saw blade
(6) and rotary table (14).
• Adjust the adjusting screw (28) until the angle between
the saw blade (6) and rotary table (14) is precisely 45°.
• It is not necessary to fix this setting because it is
maintained by the spring pretension.
• Subsequently check the position of the angle indi-
cator. If necessary loosen the pointer (19) using a
Philips screwdriver, set to position 45° on the angle
scale (18) and re-tighten the retaining screw.
8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1/2/12)
The crosscut saw can be used to make mitre cuts of 0°
- 45° in relation to the work face.
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (16a) must be fixed at the out-
er position.
• Open the set screw (16b) for the adjustable stop rail
(16a) and push the adjustable stop rail outwards.
• The adjustable stop rail (16a) must be fixed far
enough in front of the innermost position that the dis-
tance between the stop rail (16a) and the saw blade
(6) amounts to a maximum of 8 mm.
26 GB
• Before making a cut, check that the stop rail (16a) and
the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22) and use the handle (1) to
angle the machine head (4) to the left, until the point-
er (19) indicates the desired angle measurement on
the scale (18).
• Re-tighten the fixing screw (22).
• Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°
(Fig. 2/4/13)
The crosscut saw can be used to make mitre cuts to
the left of 0°- 45° in relation to the work face and, at the
same time, 0° - 45° to the left or 0° - 45° to the right in
relation to the stop rail (double mitre cut).
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (16a) must be fixed at the out-
er position.
• Open the set screw (16b) for the adjustable stop rail
(16a) and push the adjustable stop rail outwards.
• The adjustable stop rail (16a) must be fixed far
enough in front of the innermost position that the dis-
tance between the stop rail (16a) and the saw blade
(6) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (16a) and
the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to its upper position.
• Release the rotary table (14) by loosening the set
screw (26).
• Using the handle (11), set the rotary table (14) to the
desired angle (refer also to point 8.4 in this regard).
• Re-tighten the set screw (26) in order to secure the
rotary table.
• Undo the locking screw (22) and use the handle (1) to
tilt the machine head (4) to the left until it coincides
with the required angle value (in this connection see
also section 8.6).
• Re-tighten the fixing screw (22).
• Cut as described under section 8.3.
8.8 Limiting the cutting depth (Fig. 3/14)
• The cutting depth can be infinitely adjusted using the
screw (24). To do this loosen the knurled nut on the
screw (24). Move the stop for the cutting depth limi-
tre (25) to the outside. Turn the screw (24) in or out
to set the required cutting depth. Then re-tighten the
knurled nut on the screw (24).
• Check the setting by completing a test cut.
8.9 Sawdust bag (Fig. 1)
The saw is equipped with a debris bag (17) for sawdust
and chips. Squeeze together the metal ring on the dust
bag and attach it to the outlet opening in the motor ar-
ea. The debris bag (17) can be emptied by means of a
zipper at the bottom.