Operation; Technical Data; Maintenance And Care - Renkforce 1374782 Bedienungsanleitung

• Attach the motor casing to the ceiling or a suitable traverse. Only use suitable instal-
lation material.
• Attach the motor casing with four suitable screws on the installation area or use the
folding frame to hang it on a suitable ceiling hook.

Operation

L ight effect devices are not suitable for continuous use. Strict adherence to
operation pauses increases the service life of the product significantly.
• With the switch on the engine unit, the LED mirror ball is turned on and off and the
operating mode is set:
Position 0: Device is switched off
Position I: The device is switched on and the LEDs light permanently
Position II: The device is switched on and the LEDs flash with the beat of the music
• During the operation, the LED mirror ball rotates and different coloured LEDs light up
out of the mirror ball from the engine unit. This projects coloured light spots into the
room.
If the LEDs in the music-controlled operation do not flash with the beat of
the music, make the music louder or bring the LED mirror ball closer to the
source of the sound.
Handling
• Never operate the device with damaged housing or missing covers.
• Check the suspension points and the chain regularly to prevent falling.
• Never switch on the device immediately after it has been taken from a cold to a
warm environment. The condensation that forms might damage the device. Allow
the device to reach room temperature. Wait until the condensation has evaporated.
• Remove the batteries from the battery compartment when unused for a long period
of time.
Maintenance and care
M ake sure that the inside of the device does not get wet or damp.
M ake sure that the area below the place of mounting is blocked off during
installation and service work.
The product should be cleaned regularly to remove dust, etc.
The outside of the device should be cleaned with a soft, dry or slightly damp cloth only.
Never use caustic cleaning agents or chemical solutions as the surface of the engine
unit/the mirror ball could be damaged.
Due to the long service life of the LEDs, there is no need to change the light bulbs.
Disposal
a) Product
Electronic devices are recyclables and must not be disposed of in the
household waste!
Please dispose of the product, when it is no longer of use, according to the
current statutory requirements.
Remove the batteries that may be inserted and dispose of them separately
from the product.
b) Batteries and rechargeable batteries
As the end user, you are required by law (Battery Regulation) to return used batteries.
Do not dispose of used batteries in the household waste!
Batteries/rechargeable batteries containing hazardous substances are la-
belled with the symbol shown to indicate that disposal in household waste
is forbidden. The symbols of the critical heavy metals are: Cd=cadmium,
Hg=mercury, Pb=lead (marking can be seen on the battery / rechargeable
battery, e.g., underneath the refuse bin symbol shown on the left).
You can return your used batteries/rechargeable batteries free of charge at the official
collection points of your community, in our stores, or at places where batteries or
rechargeable batteries are sold!
You thereby fulfil your statutory obligations and contribute to the protection of the
environment.
Technical data
Operating voltage....................................... 4.5 V/DC
Batteries ...................................................... 3x 1.5 V Mignon cell (AA)
Illuminant ..................................................... 18 LEDs (4x red, 4x blue, 4x green, 6x white)
Rotation speed............................................ 5 - 6 U/min
Ball diameter............................................... 20 cm
Dimensions engine unit (D x H)................ 130 x 52 mm
Chain length ................................................ approx. 23 cm
Weight .......................................................... 905 g
Operating temperature range .................. +10 °C to +35 °C
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.