Turner Safety Instructions - Protool AGP 230-22 Bedienungsanleitung

which the power tool was not designed cannot
be adequately guarded and are unsafe.
b) The guard must be securely attached to
the power tool and positioned for maximum
safety, so the least amount of wheel is
exposed towards the operator. The guard
helps to protect operator from broken wheel
fragments and accidental contact with wheel.
c) Wheels must be used only for recom-
mended applications. For example: do not
grind with the side of cut-off wheel. Abrasive
cut-off wheels are intended for peripheral grind-
ing, side forces applied to these wheels may
cause them to shatter.
d) Always use undamaged wheel flanges that
are of correct size and shape for your selected
wheel. Proper wheel flanges support the wheel
thus reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different from
grinding wheel flanges.
e) Do not use worn down wheels from larger
power tools. Wheel intended for larger power
tool is not suitable for the higher speed of a
smaller tool and may burst.
Additional Safety Warnings Specific
for Abrasive Cutting-Off Operations:
a) Do not "jam" the cut-off wheel or apply
excessive pressure. Do not attempt to make
an excessive depth of cut. Overstressing the
wheel increases the loading and susceptibility to
twisting or binding of the wheel in the cut and
the possibility of kickback or wheel breakage.
b) Do not position your body in line with and
behind the rotating wheel. When the wheel, at
the point of operation, is moving away from your
body, the possible kickback may propel the
spinning wheel and the power tool directly at you.
c) When wheel is binding or when interrupting
a cut for any reason, switch off the power
tool and hold the power tool motionless until
the wheel comes to a complete stop. Never
attempt to remove the cut-off wheel from the
cut while the wheel is in motion otherwise
kickback may occur. Investigate and take
corrective action to eliminate the cause of wheel
binding.
d) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully reenter the cut. The wheel may bind,
walk up or kickback if the power tool is restarted
in the workpiece.
e) Support panels or any oversized work-
piece to minimize the risk of wheel pinching
and kickback. Large workpieces tend to sag
under their own weight. Supports must be placed
under the workpiece near the line of cut and
near the edge of the workpiece on both sides of
the wheel.
f) Use extra caution when making a "pocket
cut" into existing walls or other blind areas.
The protruding wheel may cut gas or water
pipes, electrical wiring or objects that can cause
kickback.
Safety Warnings Specific for Sanding
Operations:
a) Do not use excessively oversized sanding
disc paper. Follow manufacturers recom-
mendations, when selecting sanding paper.
Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and
may cause snagging, tearing of the disc or
kickback.
Safety Warnings Specific for Wire
Brushing Operations:
a) Be aware that wire bristles are thrown by
the brush even during ordinary operation.
Do not overstress the wires by applying
excessive load to the brush. The wire bristles
can easily penetrate light clothing and/or skin.
b) If the use of a guard is recommended for
wire brushing, do not allow any interference
of the wire wheel or brush with the guard.
Wire wheel or brush may expand in diameter
due to work load and centrifugal forces.

Turner safety instructions:

� The storage and handling of grinding wheels
must be carried out in compliance with the
manufacturer's instructions.
� Make sure that the pliable washers of the
grinding tool arte installed if such washers
are supplied with the tool and their use is
required.
� Do not use separated reduction housings or
adaptors to adjust grinding wheels with larger
holes.
� In the case of equipment designed for use
with an internal-threaded wheel make sure
that the thread in the wheel is long enough
with respect to the length of the spindle.
� The machine may not be used in damp and
wet spaces, outdoor when it is rainy, foggy or
snowy or in the explosive environment.
� Before use always inspect the flexible lead
and the plug. Have the defects repaired by a
specialist repair shop.
� Outside the premise use only approved
extension leads and cable connections.
� It is not allowed to grind or cut asbestos
materials.
13