Scheppach 4903303901 Originalbetriebsanleitung Seite 19

13. Maintain tools with care
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating
and changing accessories. Inspect tool cords
periodically and, if damaged, have repaired by
authorized service facility. Inspect extension
cords periodically and replace if damaged. Keep
handles dry, clean and free from oil and grease.
14. Disconnect tools
When not in use, before servicing, and when
changing accessories.
15. Remove adjusting keys and wrenches
Form the habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
16. Avoid unintentional starting
Don't carry plugged-in tool with finger on switch.
Be sure switch is off when plugging in.
17. Outdoor use extension cords
When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
18. Stay alert
Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
19. Check damaged parts
Before further use of the tool, a guard or other
part that is damaged should be carefully checked
to determine that it will operate properly and per-
form its intended function. Check for alignment of
moving parts, binding of moving parts, breakage
of parts, mounting, and any other conditions that
may affect its operation. A guard or other part
that is damaged should be properly repaired or
replaced by an authorized service-center unless
otherwise indicated elsewhere in this instructions
manual. Have defective switches replaced by
an authorized service-center. Do not use tool if
switch does not turn it on and off
20. m Warning!
The use of any other accessory or attach
other than recommended it this operating
instruction or the catalog may present a risk of
personal injury.
21. Have your tool repaired by an expertThis elec-
tric appliance is in accordance with the relevant
safety rules repairing of electric appliances may
be carried out only by experts otherwise it may
cause considerable danger for the user.
22. Connect the dust extraction device
Wherever there are facilities for fitting a dust
extraction system, make sure it is connected and
used.
General safety regulations and accident preven-
tion
It is essential that you read the safety regulations
and operating instructions in their entirety and fol-
low the information contained therein in order to
eliminate the possibility of an accident or potentially
dangerous situation from occurring while working
with the machine.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Always check the device, the mains cable and
the plug before using the device. Only operate
the tool when it is in good working order and is
not damaged in any way. Damaged parts have
to be replaced immediately by a qualified electri-
cian.
• Always pull the power plug out of the socket
outlet before doing any work on the machine,
before changing tools and whenever the ma-
chine is not being used.
• To prevent damage to the power cable, always
lead the power cable away from the rear of the
machine.
• Keep the tools in a safe place and out of the
reach of children.
Use on materials containing asbestos is prohib-
ited.
Note the corresponding accident prevention regula-
tion issued by the professional associations in your
country.
• Use only original replacement parts.
• Repairs may only be carried out by a qualified
electrician.
• The machine may exceed 91.5 dB at the work-
place. The operator will require noise protection
measures and ear muffs if this is the case. The
noise of this electric tool is measured in accord-
ance with IEC 59 CO 11, IEC 704, DIN 45635
part 21, NFS 31-031 (84/537/EEC).
• Ensure that you maintain a steady foothold.
Avoid abnormal working postures.
• Do not expose your electric tool to rain. Never
use electric tools in damp or wet locations or
near flammable liquids or gases.
• Protect the mains cable from becoming dam-
aged by oil, solvents and sharp edges.
• Keep your work area tidy.
• Make sure that the switch is turned off when
connecting the tool to the power supply.
ment • Wear suitable work clothes. Never wear loose
fitting clothes and jewellery. Wear a hair net if
you have long hair.
• For your own safety, use only accessories and
auxiliary equipment from the manufacturer of
your electric tool.
•
Always wear safety goggles, protective gloves
and ear-muffs while carrying out grinding,
brushing and cutting jobs.
• Check that the rotating speed shown on the
wheel is equal to or higher than the rated speed
of rotation for the tool.
• Make sure that the grinding wheel is of the cor-
rect size for the grinder.
• Grinding wheels must be handled and stored
with care in accordance with the manufacturer's
instructions. Examine the grinding wheel each
time before using it. Never use grinding wheels
which have parts broken off or are cracked or in
any other way damaged.
GB
19 / 152