Operation - EINHELL 43.003.17 Originalbetriebsanleitung

Anleitung_TH_MS_2112_T_SPK1__ 03.05.13 07:58 Seite 17
Once the turntable (8) is engaged, the setting
must also be secured by tightening the locking
screw (10).
If different angle settings are required, the
n
turntable (8) may be secured in position using
only the locking screw (10).
Lightly press the machine head down while at
n
the same time pulling the retaining pin (23) out
from the motor mounting; this causes the saw to
move down to the lower working position. Turn
the safety pin (23) through 90° so that the
machine head remains unlocked.
Swing up the machine head.
n
When the tightening screw (22) is loosened, you
n
can tilt the machine head to the left by up to 45°.
Check the mains voltage against the voltage
n
details on the rating plate to ensure they are
identical and plug in the machine.
6.4 Precision adjustment of the stop for crosscut
90° (Fig. 19/20)
Lower the machine head and fasten in place with
n
the safety pin (23).
Slacken the tightening screw (22).
n
Place the angular stop (a) between the blade (5)
n
and the turntable (8).
Slacken the counternut (b) and adjust the
n
adjustment screw (c) until the angle between the
blade (5) and the turntable (8) equals 90°.
Retighten the counternut (b) to secure this
n
setting.
6.5 Precision adjustment of the stop for miter cut
45° (Fig. 19/20)
Lower the machine head and fasten in place with
n
the safety pin (23).
Fasten the turntable (8) in 0° position.
n
Undo the tightening screw (22) and use the
n
handle (2) to tilt the machine head to the left until
it coincides at 45°.
Place the 45° stop angle (f) between the blade
n
(5) and the turntable (8).
Slacken the counternut (d) and adjust the
n
adjustment screw (e) until the angle between the
blade (5) and the turntable (8) equals 45°.
Retighten the counternut (d) to secure this
n
setting.
6.6 Sawdust extraction (Fig. 18)
The saw is equipped with an extractor port (31)
n
for sawdust and chips.
This means that it can be connected to all
n
extractors with ease.
Never use the equipment without the suction
n
function. Regularly check and clean the suction
channels.
6.7 Changing the saw blade (Fig. 7/14/15)
Pull the mains plugs, the saw blade must come
n
to a complete standstill.
Set the saw to crosscut mode (see 6.2.1).
n
Undo the two Allen screws (32) and remove the
n
splitter (30) including the saw blade guard (17).
Remove the Philips screws (33) and the table
n
insert (34).
Lock the outer flange (35) using the supplied face
n
spanner (21) and turn out the screw clockwise
using the Allen key (19) (important: left-hand
thread).
Take the saw blade (5) off the inner flange and
n
pull it out upwards through the slit in the saw
bench (16).
Thoroughly clean the outer and inner flanges and
n
the motor shaft before you fit and secure the new
saw blade. Important. The cutting angle of the
teeth (i.e. the direction of rotation of the saw
blade) must coincide with the direction of the
arrow on the housing.
Refit and secure the table insert (34), splitter (30)
n
and saw blade guard (17).
When you secure the splitter (30) ensure that the
n
distance between the teeth of the saw blade and
the splitter is min. 3 mm and max. 5 mm (Fig. 7).
Check to make sure that all safety devices are
n
properly mounted and in good working condition
before you begin working with the saw again.

7. Operation

After every new adjustment we recommend you
to make a trial cut in order to check the new
settings.
Important: The machine is fitted with an overload
switch (Fig. 17/Item b). If the machine is
overloaded, it will cut out automatically.
You must wait a few minutes for the machine to
cool before restarting. Then press the overload
switch (b) again and the machine is ready for
use.
7.1 Use as a bench saw (Fig. 1-9)
Setting the saw to bench mode (see 6.2.2)
Take extra care when starting the cut.
7.1.1 On/Off switch (Fig. 4)
The saw can be switched on by pressing the
n
green pushbutton (a). Wait for the blade (5) to
reach its maximum speed before starting the cut.
The red pushbutton (b) has to be pressed to
n
switch off the saw.
GB
17