Operation - EINHELL TC-MS 3017 T Originalbetriebsanleitung

6. Operation

After every new adjustment we recommend
you to make a trial cut in order to check the
new settings.
Warning! To make 90° crosscuts, the adjustable
stop rail (39) must be fi xed at the inner position:
•
Undo the locking screw (40) of the adjustable
stop rail and push the adjustable stop rail in-
wards.
•
The adjustable stop rail (39) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (39) and
the saw blade (5) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking screw (40) again.
Warning! To make 0°-45° miter cuts (with the
saw head inclined or the turntable set at an ang-
le), the adjustable stop rail (39) must be fi xed at
an outer position.
•
Undo the locking screw (40) of the adjustable
stop rail and push the adjustable stop rail out-
wards.
•
The adjustable stop rail (39) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (39) and
the saw blade (5) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking screw (40) again.
6.1 Use as a bench saw (Fig. 1)
Setting the saw to bench mode (see 5.2.2./6)
Take extra care when starting the cut.
6.1.1 On/Off switch (Fig. 18)
•
The saw can be switched on by pressing the
green pushbutton (I). Wait for the blade (5)
to reach its maximum speed before starting
the cut.
•
The red pushbutton (0) has to be pressed to
switch off the saw.
6.1.2 Adjusting the cutting depth
•
Undo the locking screws (15, 24) and lower
the saw table until the desired cutting height
is reached for the saw blade.
•
Tighten the two locking screws again.
GB
6.1.3 Longitudinal cuts (Figure 20-22)
•
•
•
•
•
•
•
•
•
•
•
•
6.1.4. Making cross cuts (Fig. 20-22)
•
•
•
•
•
•
www.sidirika-nikolaidi.gr
- 26 -
Undo the knurled screw (25) and set the
cross and parallel stop (18) to 90°. Tighten
the knurled screw (25) again.
Fit the parallel stop (18) from the right into the
front groove in the saw bench (16).
Undo the two knurled screws (26). Carefully
push the stop rail (27) to over the middle of
the saw blade (5) and secure it.
Set the parallel stop (18) to the required di-
mension using the scale (c) on the saw bench
(16) and secure it with the locking screw (28).
Switch on the saw by pressing the green
button (I).
Slide the workpiece slowly and precisely
along the parallel stop (18) to the saw blade
(5).
The top saw blade guard (17) will open auto-
matically and the workpiece moves forward.
Important: For workpiece widths below 120
mm a push stick (29) must be used in the
area near the saw blade (5) (see Fig. 21)
(supplied). For workpiece widths below 30
mm a push block (d) must be used to move
the workpiece . The push block is not
supplied. (Available from your specialist
dealer)
Always push the workpiece through to the
end of the splitter (30).
After completing the cut the safety hood (17)
will close again automatically to cover the
saw blade (5).
Switch off the saw again.
Important: Secure long workpieces against
falling off at the end of the cut (e.g. with a rol-
ler stand etc.) (e.g. roller table etc.)
Fit the cross parallel stop (18) from the front
into the side groove in the saw bench (16).
Tighten the locking screw (28) until the cross
and parallel stop (18) can be moved in the
groove in the saw bench (16) with a little play.
Undo the screw (25), set the cross stop (18)
to the required angle and secure it.
Undo the two knurled screws (26) and slide
the stop rail (27) to the left until it do not touch
the saw blade guard (17) when it is moved
forwards. Retighten the knurled screws (26).
Switch on the saw.
Press the workpiece firmly against the stop
rail (27) and slide it slowly into the saw blade
(5) together with the cross and parallel stop
(18) to complete the cut.