Operation - EINHELL TC-MS 2112 T Originalbetriebsanleitung

the blade (5) and the turntable (8) equals 45°.
•
Retighten the counternut (d) to secure this
setting.
5.6 Sawdust extraction (Fig. 18)
•
The saw is equipped with an extractor port
(31) for sawdust and chips.
•
This means that it can be connected to all
extractors with ease.
•
Never use the equipment without the suction
function. Regularly check and clean the suc-
tion channels.
5.7 Changing the saw blade (Fig. 7/14/15)
•
Pull the mains plugs, the saw blade must
come to a complete standstill.
•
Set the saw to crosscut mode (see 5.2.1).
•
Undo the two Allen screws (32) and remove
the splitter (30) including the saw blade guard
(17).
•
Remove the Philips screws (33) and the table
insert (34).
•
Lock the outer flange (35) using the supplied
face spanner (21) and turn out the screw
clockwise using the Allen key (19) (important:
left-hand thread).
•
Take the saw blade (5) off the inner flange
and pull it out upwards through the slit in the
saw bench (16).
•
Thoroughly clean the outer and inner flanges
and the motor shaft before you fit and secure
the new saw blade. Important. The cutting
angle of the teeth (i.e. the direction of rotation
of the saw blade) must coincide with the di-
rection of the arrow on the housing.
•
Refit and secure the table insert (34), splitter
(30) and saw blade guard (17).
•
When you secure the splitter (30) ensure that
the distance between the teeth of the saw
blade and the splitter is min. 3 mm and max.
5 mm (Fig. 7).
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
Anl_TC_MS_2112_T_SPK1.indb 24 Anl_TC_MS_2112_T_SPK1.indb 24
GB

6. Operation

After every new adjustment we recommend
you to make a trial cut in order to check the
new settings.
Important: The machine is fi tted with an over-
load switch (Fig. 17/Item b). If the machine is
overloaded, it will cut out automatically.
You must wait a few minutes for the machi-
ne to cool before restarting. Then press the
overload switch (b) again and the machine is
ready for use.
Warning! To make 90° crosscuts, the adjustable
stop rail (39) must be fi xed at the inner position:
•
Undo the locking screw (40) of the adjustable
stop rail and push the adjustable stop rail in-
wards.
•
The adjustable stop rail (39) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (39) and
the saw blade (5) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking screw (40) again.
Warning! To make 0°-45° miter cuts (with the
saw head inclined or the turntable set at an ang-
le), the adjustable stop rail (39) must be fi xed at
an outer position.
•
Undo the locking screw (40) of the adjustable
stop rail and push the adjustable stop rail out-
wards.
•
The adjustable stop rail (39) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (39) and
the saw blade (5) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking screw (40) again.
6.1 Use as a bench saw (Fig. 1-9)
Setting the saw to bench mode (see 5.2.2)
Take extra care when starting the cut.
6.1.1 On/Off switch (Fig. 4)
•
The saw can be switched on by pressing the
green pushbutton (a). Wait for the blade (5)
to reach its maximum speed before starting
the cut.
•
The red pushbutton (b) has to be pressed to
- 24 -
18.09.2015 09:06:54 18.09.2015 09:06:54