Scheppach 5906120901 Originalbetriebsanleitung Seite 26

- Do not use any faulty or damaged connection
cables.
- Do not use any power tool on which the switch
cannot be switched on and off.
15. Have your power tool repaired by a qualified elec-
trician
- This power tool conforms to the applicable safe-
ty regulations. Repairs may only be performed
by an electrician using original spare parts. Oth-
erwise accidents can occur.
16. Attention!
- For your own safety, only use accessories and
additional equipment that are indicated in the op-
erating manual or have been recommended or
indicated by the manufacturer. Use of other tool
attachments or accessories that those recom-
mended in the operating manual or in the cata-
logue could represent a personal danger to you.
17. Noise
- Wear hearing protection when using the com-
pressor.
18. Replacing the connection cable
- If the connection line is damaged, it must be re-
placed by the manufacturer or an electrician to
avoid danger. There is a risk of electric shock.
19. Inflating tyres
- Check the tyre pressure immediately after filling
using a suitable pressure gauge, e.g. at a petrol
station.
20. Street-legal compressors in construction site op-
eration
- Ensure that all hoses and fixtures are suitable
for the maximum permissible working pressure
of the compressor.
21. Set-up location
- Only set up the compressor on a flat surface.
22. In case of pressures above 7 bar, it is recommend-
ed to equip supply hoses with a safety cable (e.g.
a wire rope).
23. Avoid over-stressing the piping system by using
flexible hose connections to prevent kinking.
24. Make sure that the oil cooling devices are kept
clean and that the protective devices are kept in
good operating condition.
25. Risk of burns from hot oil
- Wear suitable protective gloves.
- Never work with the compressor near naked
flames.
- Be careful not to spill oil.
26. Starting the motor is forbidden if the temperature
is below 0°C.
26 | GB
27. Use a residual current circuit breaker with a trigger
current of 30 mA or less. Use of an RCD reduces
the risk of electric shock.
m WARNING! This power tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain cir-
cumstances. In order to prevent the risk of serious
or deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operating
the power tool.
ADDITIONAL SAFETY INSTRUCTIONS
Observe the corresponding operating manuals of
the respective compressed air tools / compressed
air attachments! The following general instructions
must also be observed:
Safety instructions for working with compressed
air and air blow guns
• Ensure there is sufficient distance to the product, at
least 2.50 m, and keep the compressed air tools /
compressed air attachments away from the com-
pressor during operation.
• Compressor pump and lines reach high tempera-
tures during operation. Touching them will cause
burns.
• The air which is sucked in by the compressor must
be kept free of impurities that could cause fires or
explosions in the compressor pump.
• When disconnecting the hose coupling, hold the
coupling piece of the hose firmly with your hand.
• This will ensure that you avoid injuries caused by the
hose recoiling.
• Wear safety goggles and a respirator when working
with the compressed air pistol. Dusts are harmful to
health! Foreign objects or blown off parts can easily
cause injuries.
• Do not blow on people or clean clothing whilst on the
body with the air blow gun. Danger of injury!
Safety instructions when using spraying attach-
ments (e.g. paint sprayers):
• Keep the spray attachment away from the compres-
sor when filling so that no liquid comes into contact
with the compressor.
• Never spray in the direction of the compressor when
using the spraying attachments (e.g. paint sprayers).
Moisture can lead to electrical hazards!
www.scheppach.com