Residual Risks - Scheppach Hm80L Original Bedienungsanleitung

Make sure that fixed reducer rings for securing
7
the insertion tool have the same diameter and
have at least 1/3 of the cutting diameter.
8 Make sure that fixed reducer rings are parallel
to each other.
Handle insertion tool with caution. They are
9
ideally stored in the originally package or spe-
cial containers. Wear protective gloves in order
to improve grip and to further reduce the risk of
injury.
10 Prior to the use of insertion tools, make sure
that all protective devices are properly fas-
tened.
Prior to use, make sure that the insertion tool
11
meets the technical requirements of this electric
tool and is properly fastened.
12 Only use the supplied saw blade for cutting
wood, never for the processing of metals.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
0
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with un-
protected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting
surfaces and persons or animals. Even a laser
beam with a low output can cause damage to the
eyes.
• Caution - methods other than those specified
here can result in dangerous radiation exposure.
• Never open the laser module. Unexpected expo-
sure to the beam can occur.
• If the mitre saw is not used for an extended pe-
riod of time, the batteries should be removed.
• The laser may not be replaced with a different
type of laser.
• Repairs of the laser may only be carried out by
the laser manufacturer or an authorised repre-
sentative.
Safety instructions for handling batteries
1 Always make sure that the batteries are
inserted with the correct polarity (+ and –), as
indicated on the battery.
Do not short-circuit batteries.
2
Do not charge non-rechargeable batteries.
3
4 Do not overcharge batteries!
24 GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Do not mix old and new batteries or batteries
5
of different types or manufacturers! Replace
an entire set of batteries at the same time.
6 Immediately remove used batteries from the
device and dispose of them properly!
Do not allow batteries to heat up!
7
Do not weld or solder directly on batteries!
8
Do not dismantle batteries!
9
10 Do not allow batteries to deform!
11 Do not throw batteries into fire!
12 Keep batteries out of the reach of children.
Do not allow children to replace batteries with-
13
out supervision!
Do not keep batteries near fire, ovens or
14
other sources of heat. Do not use batteries in
direct sunlight or store them in vehicles in hot
weather.
15 Keep unused batteries in the original packag-
ing and keep them away from metal objects.
Do not mix unpacked batteries or toss them
together! This can lead to a short-circuit of the
battery and thus damage, burns or even the
risk of fire.
16 Remove batteries from the equipment when it
will not be used for an extended period of time,
unless it is for emergencies!
NEVER handle batteries that have leaked
17
without appropriate protection. If the leaked
fluid comes into contact with your skin, the
skin in this area should be rinsed off under
running water immediately. Always prevent the
fluid from coming into contact with the eyes
and mouth. In the event of contact, please
seek immediate medical attention.
Clean the battery contacts and corresponding
18
contacts in the device prior to inserting the
batteries.

Residual risks

The machine has been built according to the
state of the art and the recognised technical
safety requirements. However, individual residu-
al risks can arise during operation.
• Health hazard due to electrical power, with the
use of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still
remain.
• Residual risks can be minimised if the „safety
instructions" and the „Proper use" are observed
along with the whole of the operating instruc-
tions.
• Do not load the machine unnecessarily: exces-
sive pressure when sawing will quickly damage
the saw blade, which results in reduced output of
the machine in the processing and in cut preci-
sion.