Residual Risks; Technical Data - Scheppach Hs80 Original Bedienungsanleitung

12. The saw blade supplied should only be used for
sawing wood and never for working metal.
13. Use the saw blade intended for the material to be
processed.
14. Use only a saw blade with a diameter that matches
the specifications on the saw.
15. Use only saw blades that are marked with an equal
or higher rotational speed than that marked on the
power tool.
16. Use only saw blades recommended by the manu-
facturer which conform to EN 847-1, if intended for
cutting wood or similar materials.
17. Wear suitable personal protective equipment,
such as:
– hearing protection;
– protective gloves when handling saw blades.
18. Use only saw blades recommended by the man-
ufacturer which conform to EN 847-1. Warning!
When changing the saw blade, make sure that the
cutting width is not smaller and the thickness of
the saw blade is not greater than the thickness of
the splitter.
19. When sawing wood and plastics, avoid overheat-
ing the saw teeth. Reduce the feed speed to avoid
the plastic melting.

Residual Risks

This power tool has been constructed in accord-
ance with the latest technology and the generally
recognised safety regulations. Nevertheless, it is
possible that individual residual risks may occur
during operation.
• Electrical hazard if improper electrical connection
cables are used.
• In addition, concealed residual risks may be present
in spite of all the precautions that have been taken.
• Residual risks can be minimised by observing the
„Safety instructions" and „Use in accordance with
the designated purpose", as well as the operating
instructions.
• Do not put any unnecessary stresses on the ma-
chine: excessive pressure during sawing will quickly
damage the saw blade. This may result in a reduc-
tion in the performance of the machine, as well as a
reduction in the cutting accuracy.
• Avoid switching the machine on by accident: when
inserting the plug into the socket, the power button
must not be pressed.
• Use the tool which is recommended in this manu-
al. This will ensure the optimal performance of your
saw.
• Keep your hands away from the working area when
the machine is in operation.
• Before you carry out any adjustments or servicing
work, turn the device off and remove the mains plug.

6. Technical data

AC motor .......................................... 220-240 V~ 50 Hz
Power consumption ............................. 1200 Watt (S1*)
1500 Watt (S6 25%)
Idle speed n
Hard metal saw blade ................ø 210 x ø 30 x 2.6 mm
Number of teeth ......................................................... 24
Riving knife thickness ........................................2.0 mm
Min. size of workpiece W x L x H ......... 10 x 50 x 1 mm
Table size ................................................485 x 445 mm
Table width extension ............................. 485 x 515 mm
Table size max. .......................................485 x 630 mm
Cutting height max. 45° ......................................45 mm
Cutting height max. 90° ......................................48 mm
Tilting saw blade ............................................ 0-45° left
Suction connection ..........................................ø 35 mm
Weight ...................................................... approx. 14 kg
Machine size (with extension)
W x L x H .......................................485 x 630 x 440 mm
*S1: Continuous operation at constant load
**S6 25% operating mode:
Continuous duty with intermittent loading (operating
time 10 min.)
In order avoid impermissible overheating of the motor,
the motor should be driven for only 25% of the operat-
ing time with the stipulated nominal power and must
then continue to run with no load for the remaining 75%
of the operating time.
Noise
The total noise values were determined in accordance
with EN 62841.
Sound pressure level L
Uncertainty K
Sound power level L
Uncertainty K
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total
vibration values (vector sum - three directions) deter-
mined in accordance with EN 62841.
www.scheppach.com
.................................................. 4800 rpm
0
................................. 87.5 dB
pA
..................................................... 3 dB
pA
...................................100.5 dB
WA
..................................................... 3 dB
WA
GB | 35