Scheppach 5905112902 Originalbetriebsanleitung Seite 28

• Do not load the machine so much that it comes to
a standstill.
• Make sure that cut-off pieces of wood are not caught
by the sprocket of the saw blade and flung away.
• Never remove loose fragments, chips or jammed
wood pieces from the running saw blade unless a
push stick is used.
• To rectify faults or remove jammed pieces of wood,
switch the machine off. - Pull out the mains plug -
• Renew the table insert if the sawing gap has become
worn. - Pull out the mains plug -
• Only carry out modifications, adjustments, meas-
urements and cleaning work when the engine is
switched off. - Pull out the mains plug -
• Before switching on, make sure that keys and ad-
justing tools are removed.
• Switch off the engine and pull out the mains plug
when leaving the work station.
• All protective and safety equipment must be reas-
sembled immediately after repair or when mainte-
nance is completed.
• The safety, operating and maintenance information of
the manufacturer, as well as the dimensions specified
in the technical data, must be observed.
• The applicable accident prevention regulations and
the other generally accepted safety rules must be
observed.
• Observe the instructions of the employers' liability
insurance association (VBG 7j).
• The circular saw must be connected to a 400 V
socket with a 16 A slow-blow fuse.
• Do not use low-output machines for heavy work.
• Do not use the cable for purposes for which it is
not intended!
• Make sure that you have secure footing and always
maintain your balance.
• Check the power tool for potential damage!
• Protective devices or other parts with minor dam-
age must be carefully inspected to ensure that they
function correctly and as intended prior to continued
use of the tool.
• Check whether the moving parts function faultlessly
and do not jam or whether parts are damaged. All
parts must be correctly mounted and all conditions
must be fulfilled to ensure fault-free operation of
the tool.
• Damaged protective devices and parts must be
repaired properly or replaced by a recognised spe-
cialist workshop unless otherwise specified in the
usage instructions.
28 | GB
• Have damaged switches replaced by a customer
service workshop.
• This tool conforms to the applicable safety regulations.
Repairs may only be performed by an electrician using
original spare parts. Otherwise, accidents can occur.
• If necessary, wear suitable personal protective
equipment. This could include:
– Hearing protection to avoid the risk of becoming
hearing impaired;
– Respiratory protection to avoid the risk of inhaling
harmful dust.
• Wear gloves when handling saw blades and rough
materials. Saw blades must be carried in a container
whenever practical.
• The operator must be informed about the conditions
that affect the noise levels (e.g. saw blades designed
to reduce noise, care of saw blade and machine).
• Faults in the machine, including the guards and the
saw blade, must be reported to the person responsi-
ble for safety as soon as they are discovered.
• When transporting the machine, use only the trans-
port devices and never use the guards for handling
and transport.
• All operators must be adequately trained in the use,
setting and operation of the machine.
• Do not saw any material to be cut that contain for-
eign bodies such as wires, cables or cords.
• Only use sharp saw blades.
• The machine must be on a horizontal, level floor
during operation and the floor around the machine
must be level, well maintained and free of waste
such as chips and cut-off workpieces.
• Adequate general lighting or local lighting must be
available.
• Arrange the workpiece stack to be processed and
the finished workpieces close to the normal work-
place of the operator.
• Familiarise yourself with the safe procedures for
cleaning, maintenance and regular removal of chips
and dust to prevent the risk of fire.
• Follow the manufacturer's instructions for use, ad-
justment and repair of saw blades.
• Observe the maximum speed specified on the saw
blades.
• Ensure that the flanges used are suitable for the in-
tended application as specified by the manufacturer.
• Ensure that the protective devices and other safety
equipment required for operation of the machine are in
place, in good working order and properly maintained.
• Dust exposure is influenced by the type of material
being sawn.
www.scheppach.com