Before Commissioning - Scheppach Hms1070 Originalbetriebsanleitung

Technical data - Thicknesser
Max. planing width
Max. workpiece
thickness for
thicknesser
Max. chip take-off
Thicknesser table size
Drive
Motor
Rated input P1
Subject to technical changes!
Noise
The noise levels have been determined in accord-
ance with EN 61029.
Sound pressure level L pA
Uncertainty K pA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection.
Excessive noise can result in a loss of hearing.
Keep the noise level and vibration to a minimum!
• Only use faultless devices.
• Maintain and clean the device at regular intervals.
• Adapt your working methods to the device.
• Do not overload the device.
• Have the device checked if necessary.
• Switch the device off if it is not in use.

7. Before commissioning

Before each use, always check:
• On/off switch incl. emergency stop switch (if pres-
ent) for proper function
• Interlocked guards (Fig. 1a - Pos. 3) by succes-
sive opening of each guard to switch off the
machine and by checking that it is impossible
to switch on the machine with a guard open
• Brake
when starting work, switch on the machine and let
it come up to speed. Now switch the machine off
again. The engine must stop within 10 seconds.
Otherwise, there is a defect.
• Anti-kickback claws (Fig. 4 - Pos. 25)
at least once per work shift by inspection to check
that they are in good working condition, e.g. have
no damage to the contact surface from impact and
that the anti-kickback claws (25) fall back unhin-
dered by their own weight;
• Planer blade (Fig. 13 - Pos. 24)
must be checked for damage and correct fit.
32 | GB
254 mm
120 mm
2 mm
380 x 254 mm
230 V / 50 Hz
1500 W
97 dB
3 dB
110 dB
3 dB
www.scheppach.com
The machine may only be used if all these condi-
tions are met.
Use only saw blades that are well sharpened and
maintained. Only use blades designed for the ma-
chine.
Use wooden push blocks or push sticks that are not
defective when machining short workpieces.
Connect the machine to a dust or chippings extrac-
tion system.
Check that the stop is firmly clamped in place before
you start machining.
Ensure that you can keep your balance at all times.
Stand to the side of the machine.
Keep your hands at a safe distance from the cutting
roller and from the point where the chips are ejected
when the machine is running.
Do not start planing until the cutting roller has
reached its required speed.
Also make sure that the workpiece does not contain
any cables, ropes, cords or similar. Do not work on
wood that contains numerous knots or knotholes.
Secure long workpieces against tilting at the end of
the planing process. E.g. use roller stands or similar
devices for this.
It is strictly forbidden to remove chips or fragments
while the machine is running.
Switch the machine off immediately in the event of a
jam. Pull out the mains plug and remove the jammed
workpiece.
Set the smallest cut size after each use to prevent
the risk of injury.
m ATTENTION!
The machine must be securely fastened to the floor/
worktop with the appropriate screws / screw clamps,
as there is a risk of tipping over.
• Before connecting the machine, make certain that
the data on the type plate matches with the mains
power data.
m WARNING! Disconnect the mains plug from
the main power supply before any cleaning, adjust-
ment, maintenance or repair work!
• Check regularly that blades (24) are firmly fixed in
the blade block.
• The blades (24) must not protrude more than 1.1
mm from the blade block.
• Check the anti-kickback claws (25) regularly for
proper functioning.