• Familiarise yourself with the device by means of the
operating manual before using for the first time.
• With accessories as well as wearing parts and re
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
• When ordering please provide our article number as
well as type and year of manufacture for your equip
ment.
ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
8. Assembly
8.1 Parallel stop (fig. 2)
• Turn out the locking bolt (17) a little bit clockwise.
(The locking bolt shouldn´t fall out)
• Now set in the locking bolt (17) into the slot of the
sidewall of the parallel stop.
• Now push the parallel stop (5) to the side so that
the groove of the parallel stop (5) can be lowered
towards the screw (18)
• Now tighten the hexagon socket screw (18) with the
Allen key supplied (14).
• Now tighten the locking pin (17) again anti-clock
wise.
8.2 Crank handle for thickness planer chip depth
(fig. 3)
• The crank handle (10) will be only plugged on the
spindle (19).
8.3 Chip extractor - surface planing (fig. 4-6)
• Set the planing knife cover cpl. (13) in the upperst
position.
• Use the crank handle (10) to place the Thicknessing
table (21) in the lowest position.
• Take the chip extractor (4) and hold the switching
pins (3) beside.
Place the chip extractor (4) at a slightly slanting an
gle on the machine and push it backwards.
For this you need to hold the switching pins (3) out
wards.
• Now lock the chip extractor (4) with the switching
pins in the table. Attention! The machine won´t
start if the switching pins are incorrectly plugged in.
• Now you can fold the planing knife cover cpl. (13)
down again.
8.4 Chip extractor - thickness planing (fig. 11)
• The parallel stop (5) needs to be removed for thick
ness planing. Follow point 8.1 in reverse order.
• Now slide the planing knife cover (7) beside so that
the cutter block is completely uncovered.
• Hold the switching pins (3) outside and set the chip
extractor (4) on top of the machine.
• Now lock the chip extractor (4) with the switching
pins in the table. Attention! The machine won´t start
if the switching pins (3) are incorrectly plugged in.
9.
Before starting the equipment
m Attention!
Always make sure the device is fully assembled
before commissioning!
Before each use, check the following:
• Proper function of the on and off button, incl. the
emergency switch (if available).
• Locked disconnected protective equipment (fig
1a - pos. 3) by gradual opening of every separating
protective equipment to be able to turn the machine
off and checking that the machine cannot be turned
on whenever the protective equipment is open
• Brake Switch on the machine at the start of work
and allow the machine to reach speed. Now switch
the machine off again. The engine must come to a
standstill within 10 seconds. Otherwise, there is a
defect.
• Anti-kick claws (fig. 4 - pos. 25) at least once per
shift by a visual inspection to establish that they are
in good working order, for example, that the contact
surface has not been damaged by impacts and that
the anti-kick claws (25) fall back without hindrance
due to their own weight;
• Planing blades (fig. 13 - pos. 24) for signs of dam
age and to ensure they are positioned correctly.
The machine may only be used if all these condi-
tions are satisfied.
Use only well sharpened and maintained blades. Use
only blades that are designed for the machine.
Use pusher wood or sticks which are in perfect condi
tion for machining short workpieces.
Connect the machine to a dust and chip extractor.
www.scheppach.com
GB | 37