Scheppach HMS850 Original Bedienungsanleitung Seite 37

• Familiarise yourself with the device by means of the
operating manual before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
• When ordering please provide our article number as
well as type and year of manufacture for your equip-
ment.
ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
8. Assembly
8.1 Parallel stop (fig. 2)
• Turn out the locking bolt (17) a little bit clockwise.
(The locking bolt shouldn´t fall out)
• Now set in the locking bolt (17) into the slot of the
sidewall of the parallel stop.
• Now push the parallel stop (5) to the side so that
the groove of the parallel stop (5) can be lowered
towards the screw (18)
• Now tighten the hexagon socket screw (18) with the
Allen key supplied (14).
• Now tighten the locking pin (17) again anti-clock-
wise.
8.2 Crank handle for thickness planer chip depth
(fig. 3)
• The crank handle (10) will be only plugged on the
spindle (19).
8.3 Chip extractor - surface planing (fig. 4-6)
• Set the planing knife cover cpl. (13) in the upperst
position.
• Use the crank handle (10) to place the Thicknessing
table (21) in the lowest position.
• Take the chip extractor (4) and hold the switching
pins (3) beside.
Place the chip extractor (4) at a slightly slanting an-
gle on the machine and push it backwards.
For this you need to hold the switching pins (3) out-
wards.
• Now lock the chip extractor (4) with the switching
pins in the table. Attention! The machine won´t
start if the switching pins are incorrectly plugged in.
• Now you can fold the planing knife cover cpl. (13)
down again.
8.4 Chip extractor - thickness planing (fig. 11)
• The parallel stop (5) needs to be removed for thick-
ness planing. Follow point 8.1 in reverse order.
• Now slide the planing knife cover (7) beside so that
the cutter block is completely uncovered.
• Hold the switching pins (3) outside and set the chip
extractor (4) on top of the machine.
• Now lock the chip extractor (4) with the switching
pins in the table. Attention! The machine won´t start
if the switching pins (3) are incorrectly plugged in.
9. Before starting the equipment
m Attention!
Always make sure the device is fully assembled
before commissioning!
Before each use, check the following:
• Proper function of the on and off button, incl. the
emergency switch (if available).
• Locked disconnected protective equipment (fig
1a - pos. 3) by gradual opening of every separating
protective equipment to be able to turn the machine
off and checking that the machine cannot be turned
on whenever the protective equipment is open
• Brake Switch on the machine at the start of work
and allow the machine to reach speed. Now switch
the machine off again. The engine must come to a
standstill within 10 seconds. Otherwise, there is a
defect.
• Anti-kick claws (fig. 4 - pos. 25) at least once per
shift by a visual inspection to establish that they are
in good working order, for example, that the contact
surface has not been damaged by impacts and that
the anti-kick claws (25) fall back without hindrance
due to their own weight;
• Planing blades (fig. 13 - pos. 24) for signs of dam-
age and to ensure they are positioned correctly.
The machine may only be used if all these condi-
tions are satisfied.
Use only well sharpened and maintained blades. Use
only blades that are designed for the machine.
Use pusher wood or sticks which are in perfect condi-
tion for machining short workpieces.
Connect the machine to a dust and chip extractor.
www.scheppach.com GB | 37