Parkside Performance PWSAP 20-Li G7 Originalbetriebsanleitung Seite 6

GB
IE NI
PARKSIDE Performance Smart battery
Smart PAPS 204 A1/Smart PAPS 208 A1/
Smart PAPS 2012 A1
– Frequency ƒ ................. 2400 – 2483.5 MHz
– transmitted power ....................... ≤ 20 dBm
Cutting disc ...................................AS60TBF
(included)
Manufactured in compliance with EN
12413:2019
Disc rotational speed n
Disc speed v ............................... ≤ 80 m/s²*
0
Outside diameter .......................... Ø 125 mm
Borehole .....................................Ø 22.23 mm
Thickness ........................................≤ 1.2 mm
* The grinding disc must withstand a rota-
tional speed of 80 m/s.
Notes on noise and vibration values
Levels of noise and vibration were determ-
ined according to the standards and regula-
tions in the declaration of conformity.
CAUTION! Hearing damage! Wear ear
protection.
The specified total vibration values and the
stated noise emission values have been
measured according to a standardised test
method and can be used to compare one
power tool with another. The specified total
vibration values and the stated specified
noise emission values can also be used for a
provisional assessment of the load.
WARNING! The vibration and noise emis-
sions may deviate from the specified value
during actual use of the power tool, depend-
ing on how the power tool is being used and,
in particular, what kind of material is being
worked on. Safety measures for protection
of the operator are to be determined that are
based on an estimate of the vibration load
under the real operating conditions. All parts
of the operating cycle have to be considered
while doing so – for example, times when the
power tool is switched off and times when it
is switched on but running without any load.
WARNING! Grinding thin metal sheet or
other well vibrating structures with a large
surface area can result in increased noise
exposure and a much (up to 15 dB) high-
er overall noise emission than the specified
noise emission values. Use heavy flexible
damping mats or similar to prevent sound ra-
6
−1
.....≤ 12200 min
max
diation from such workpieces. Take into ac-
count the increased noise emission and wear
appropriate hearing protection.
X 20 V TEAM
The device is part of the X 20 V TEAM
series and can be operated with batteries
of the X 20 V TEAM series. Batteries of the
X 20 V TEAM series may only be charged
using chargers of the X 20 V TEAM series.
We recommend that you operate this ap-
pliance with the following batteries only:
PAP 20 B1, PAP 20 B3, Smart PAPS 204 A1,
Smart PAPS 208 A1, Smart PAPS 2012 A1
We recommend charging these bat-
teries with the following chargers:
PLG 20 A3, PLG 20 A4, PLG 20 C1,
PLG 20 C2, PLG 20 C3, PLG 201 A1,
PDSLG 20 A1, PDSLG 20 B1, PDSLG 20 B2,
Smart PLGS 2012 A1
Rechargeable battery and charger technical
data: See separate manual.
Safety information
This section deals with the basic safety in-
structions for using the device.
WARNING! Injury and property damage
due to improper handling of battery. Observe
the safety information and notes on charging
and proper use as shown in the instruction
manual for your battery and charger from the
series X 20 V TEAM. A detailed description
of the charging process and further informa-
tion can be found in these separate operat-
ing instructions.
Meaning of the safety information
DANGER! If you do not observe this
safety instruction, an accident will occur.
The result of which is severe bodily injury or
death.
WARNING! If you do not observe this
safety instruction, an accident may occur.
The result of which is likely severe bodily in-
jury or death.
CAUTION! If you do not observe this
safety instruction, an accident will occur. The
result of which is likely minor or moderate
bodily injury.
NOTICE! If you do not observe this safety in-
struction, an accident will occur. The result
of which is possible damage to property.